Singer SES2000 Instruction Manual - Page 80

Preparing The Machine Before, Installing The Hoop, Attaching And Removing, Embroidery Hoop

Get Singer SES2000 PDF manuals and user guides View all Singer SES2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

PREPARING THE MACHINE BEFORE INSTALLING THE HOOP 1 1. Turn hand wheel counter clockwise (toward you) until the needle comes to its highest position. ATTACHING AND REMOVING EMBROIDERY HOOP 1 (A) 1. Raise presser foot and needle, and push up lever (A) of embroidery foot with your finger and pass embroidery hoop under it.  To remove, pull the hoop forward to slide it out from underneath the embroidery foot. 2 (C) (D) 2. Attach hoop to embroidery unit by aligning hoop mounting (D) screws (D) and the grooves in hoop mounting plate, fitting projections (C) on hoop bracket into square holes (B) in hoop mounting plate. Securely tighten hoop mounting screws (D) with screwdriver.  To remove, loosen hoop mounting screws (D) and remove the hoop from the hoop bracket. NOTE: Before attaching small hoop, turn on power switch to move the carriage to embroidering standby position. Carriage Chariot Carro (B) (B) Hoop mounting plate Plaque de montage de cerceau Placa de montaje de aro 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
80
PREPARING THE MACHINE BEFORE
INSTALLING THE HOOP
1. Turn hand wheel counter clockwise (toward you) until the
needle comes to its highest position.
1
ATTACHING AND REMOVING
EMBROIDERY HOOP
1. Raise presser foot and needle, and push up lever (A) of
embroidery foot with your finger and pass embroidery hoop
under it.
To remove, pull the hoop forward to slide it out from
underneath the embroidery foot.
2. Attach hoop to embroidery unit by aligning hoop mounting
screws (D) and the grooves in hoop mounting plate, fitting
projections (C) on hoop bracket into square holes (B) in
hoop mounting plate. Securely tighten hoop mounting
screws (D) with screwdriver.
To remove, loosen hoop mounting screws (D) and remove
the hoop from the hoop bracket.
NOTE:
Before attaching small hoop, turn on power switch to
move the carriage to embroidering standby position.
(A)
2
1
(B)
(B)
(D)
(C)
(D)
Hoop mounting plate
Plaque de montage de cerceau
Placa de montaje de aro
Carriage
Chariot
Carro