Singer SES2000 Instruction Manual - Page 92

HELPFUL INFORMATION FOR, EMBROIDERING WITH FUTURA, with flashing light, beeping sound or E1 - futura embroidery machine

Get Singer SES2000 PDF manuals and user guides View all Singer SES2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

HELPFUL INFORMATION FOR EMBROIDERING WITH FUTURA 1. If stitches are missing If the embroidery machine detects that the thread has broken, it may continue to embroider up to about eight stitches without any thread (blank stitches) before it automatically stops. In such cases, use the following procedure to step back through the embroidering data to the point for continuing. 1. Press the reverse switch (stitch return) to step back through the embroidery data. The hoop will move back one stitch at a time. Step back through the data until the blank area has been completely passed over. 2. Restart the embroidery machine and continue embroidering. Embroidering direction Direction de broderie Dirección de bordado Embroidered section Section brodée Sección bordada 1357 2468 automatically stop S'arrête automatiquement Para automáticamente Blank stitches resulting from thread breakage Points vides résultant d'une rupture du fil Puntadas en blanco resultantes de ruptura de hilo 2. Computer screen says thread is broken with flashing light, beeping sound or "E1" error message, but thread is not broken. Thread path under transparent cover at top of machine is not threaded correctly (see page 18 - 19 "Setting the top thread") or you may want to cover small spool of thread with small net and use removable thread guide for large spool that are supplied with accessories. 3. When bobbin runs out of thread while sewing 1. Place the bobbin on the bobbin winder shaft and push the shaft towards the right. 2. Press the start/stop switch to begin winding. (The foot control is inoperable with the embroidery unit attached). 3. Remove the hoop from the machine, (DO NOT REMOVE YOUR FABRIC FROM THE HOOP), replace the empty bobbin and then re-insert the hoop. 4. If your design moved forward a stitch or two when you picked up the bobbin thread, you can use the reverse stitch button to move back to your original position. 92 Reverse stitch switch Touche couture arrière interruptor de puntadas hacia atrás

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
92
1. If stitches are missing
If the embroidery machine detects that the thread has
broken, it may continue to embroider up to about eight
stitches without any thread (blank stitches) before it
automatically stops.
In such cases, use the following procedure to step back
through the embroidering data to the point for continuing.
1. Press the reverse switch (stitch return) to step back
through the embroidery data. The hoop will move
back one stitch at a time. Step back through the data
until the blank area has been completely passed
over.
2. Restart the embroidery machine and continue
embroidering.
HELPFUL INFORMATION FOR
EMBROIDERING WITH FUTURA
2. Computer screen says thread is broken
with flashing light, beeping sound or “E1”
error message, but thread is not broken.
Thread path under transparent cover at top of machine is
not threaded correctly (see page 18 - 19 “Setting the top
thread”) or you may want to cover small spool of thread
with small net and use removable thread guide for large
spool that are supplied with accessories.
3. When bobbin runs out of thread while
sewing
1. Place the bobbin on the bobbin winder shaft and
push the shaft towards the right.
2. Press the start/stop switch to begin winding. (The foot
control is inoperable with the embroidery unit attached).
3. Remove the hoop from the machine, (DO NOT
REMOVE YOUR FABRIC FROM THE HOOP), replace
the empty bobbin and then re-insert the hoop.
4. If your design moved forward a stitch or two when you
picked up the bobbin thread, you can use the reverse
stitch button to move back to your original position.
Embroidered section
Section brodée
Sección bordada
Blank stitches resulting from thread breakage
Points vides résultant d’une rupture du fil
Puntadas en blanco resultantes de ruptura de hilo
Embroidering direction
Direction de broderie
Dirección de bordado
automatically stop
S’arrête automatiquement
Para automáticamente
7
5
3
8
6
4
2
1
Reverse stitch switch
Touche couture arrière
Interruptor de puntadas
hacia atrás