Sony BRCH700 Operating Instructions - Page 51

Installing the Camera, To remove the interface board, To install the camera on a desk

Get Sony BRCH700 - CCTV Camera PDF manuals and user guides
UPC - 027242684362
View all Sony BRCH700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

2 Insert an optional interface board into the card slot. Align both ends of the interface board with the sliders inside the slot, then insert the board securely as far as it will go. If you have to place the camera on an inclined surface, make sure that the inclination is less than ±15 degrees, so that the pan/tilt performance is guaranteed. Interface board (not supplied) 3 Tighten the two screws on the interface board. Notes • You should take an appropriate countermeasure to prevent the camera from falling. • Do not grasp the camera head when carrying the camera. • Do not turn the camera head by hand. Doing so may result in the camera malfunctioning. Installation and Connections To remove the interface board Loosen the two screws on the interface board and pull the board out straight and slowly. Installing the Camera To install the camera on a desk Place the camera on a flat surface. To attach the camera to a tripod Attach a tripod to the screw hole used for attaching a tripod on the bottom of the camera. The tripod must be set up on a flat surface and tightened firmly by hand. Use a tripod with screws of the following specifications. 1/4 -20UNC = 4.5 - 7 mm = 0.18 - 0.27 inches 51 Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Installation and Connections
Installation
51
2
Insert an optional interface board into the card slot.
Align both ends of the interface board with the
sliders inside the slot, then insert the board securely
as far as it will go.
3
Tighten the two screws on the interface board.
To remove the interface board
Loosen the two screws on the interface board and pull
the board out straight and slowly.
Installing the Camera
To install the camera on a desk
Place the camera on a flat surface.
If you have to place the camera on an inclined surface,
make sure that the inclination is less than ±15 degrees,
so that the pan/tilt performance is guaranteed.
Notes
•
You should take an appropriate countermeasure to
prevent the camera from falling.
•
Do not grasp the camera head when carrying the
camera.
•
Do not turn the camera head by hand. Doing so may
result in the camera malfunctioning.
To attach the camera to a tripod
Attach a tripod to the screw hole used for attaching a
tripod on the bottom of the camera.
The tripod must be set up on a flat surface and tightened
firmly by hand.
Use a tripod with screws of the following specifications.
Interface board
(not supplied)
1
/
4
-20UNC
= 4.5 – 7 mm
= 0.18 – 0.27 inches