Sony CMT-DH7BT Operating Manual - Page 66

Additional Information, Troubleshooting

Get Sony CMT-DH7BT - Micro Hi Fi Component System PDF manuals and user guides View all Sony CMT-DH7BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Additional Information Troubleshooting Should you encounter a problem with your system, do the following: 1 Make sure the power cord and speaker cords are connected correctly and firmly. 2 Find your problem in the troubleshooting checklist below and take the indicated corrective action. If the problem persists after doing all of the above, consult your nearest Sony dealer. If the STANDBY indicator flashes Immediately unplug the power cord, and check the following items.  If your system has a voltage selector, is the voltage selector set to the correct voltage?  Are you using only the supplied speakers?  Is anything blocking the ventilation holes on the rear of the system? After the STANDBY indicator  stops flashing, reconnect the power cord, and turn on the system, If the issue persists, contact your nearest Sony dealer. General The clock or timer setting is canceled.  The power cord is disconnected or a power failure occurred. Redo "Setting the clock" (page 19). If you have set the timer, redo "Waking up to music" (page 59). "- -:- -" appears in the display.  A power failure has occurred. Set the clock (page 19) and timer settings (page 59) again. There is no sound.  Press VOLUME +  repeatedly.  The headphones are connected to the PHONES jack .  Check the speaker connections (page 14).  The system is in pause mode, in Slow- motion Play or in Lock Search. Press   (or DVD   on the unit) to start the playback.  If the BLUETOOTH indicator  is lit or flashing when a function other than the Bluetooth function is selected, no sound is heard through the speakers or PHONES jack . Press and hold BLUETOOTH OPR  for about 2 seconds until the BLUETOOTH indicator  turns off. There is severe hum or noise.  A TV or VCR is placed too close to the unit. Move the unit away from the TV or VCR.  Move the unit away from the source of noise.  Connect the unit to a different wall outlet.  Install a noise filter (commercially available) to the power cord. 66GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
µµ
GB
Additional Informa
tion
Troubleshooting
Should you encounter a problem with
your system, do the following:
1
Make sure the power cord and
speaker cords are connected
correctly and firmly.
2
Find your problem in the
troubleshooting checklist below and
take the indicated corrective action.
If the problem persists aſter doing all
of the above, consult your nearest Sony
dealer.
If the STANDBY indicator flashes
Immediately unplug the power cord,
and check the following items.
If your system has a voltage
selector, is the voltage selector set
to the correct voltage?
Are you using only the supplied
speakers?
Is anything blocking the ventilation
holes on the rear of the system?
Aſter the STANDBY indicator
stops flashing, reconnect the power
cord, and turn on the system, If the
issue persists, contact your nearest
Sony dealer.
General
The clock or timer setting is canceled.
°e power cord is disconnected or a
power failure occurred. Redo “Setting
the clock” (page 19). If you have set
the timer, redo “Waking up to music”
(page 59).
“– –:– –” appears in the display.
A power failure has occurred. Set the
clock (page 19) and timer settings
(page 59) again.
There is no sound.
Press VOLUME +
repeatedly.
°e headphones are connected to the
PHONES jack
.
Check the speaker connections
(page 14).
°e system is in pause mode, in Slow-
motion Play or in Lock Search. Press
(or DVD
on the unit) to
start the playback.
If the BLUETOOTH indicator
is lit
or flashing when a function other than
the Bluetooth function is selected, no
sound is heard through the speakers
or PHONES jack
. Press and hold
BLUETOOTH OPR
for about
2 seconds until the BLUETOOTH
indicator
turns off.
There is severe hum or noise.
A TV or VCR is placed too close to the
unit. Move the unit away from the TV
or VCR.
Move the unit away from the source of
noise.
Connect the unit to a different wall
outlet.
Install a noise filter (commercially
available) to the power cord.