Sony RM-LP211 Operating Instructions - Page 15

Programming the remote

Get Sony RM-LP211 PDF manuals and user guides View all Sony RM-LP211 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Using the lists Programming the remote You can customize the remote to match the components connected to your receiver. You can even program the remote to control nonSony components and also Sony components that the remote is normally unable to control. The procedure below uses as an example a case in which a Aiwa VCR is connected to the VIDEO 2 jacks on the receiver. Before you begin note that: - You cannot change the settings of TUNER and PHONO. - The remote can control only components that accept infrared wireless control signals. Be sure to turn on the receiver and point the remote towards the receiver when performing the following procedure. 1 Press RM SET UP. The set up list appears. p IR SET MENU EDIT AUTO POWER BACK LIGHT 2 Move the easy scroll key to select "IR SET", then press the key to enter the selection. The IR SET list appears. [VIDEO 1 ] p [VIDEO 2 ] [VIDEO 3 ] 3 Move the easy scroll key to select the component ("VIDEO 2", for example), then press the key to enter the selection. The category list appears. Category? p VCR T V L D 4 Move the easy scroll key to select the category (i.e., the component that is actually connected to the corresponding jacks; in this case, "VCR"), then press the key to enter the selection. The maker list appears. Maker? p Sony VTR1 Sony VTR2 Sony VTR3 5 Move the easy scroll key to select the maker of the component ("Aiwa", for example), then press the key to enter the selection. When programming the remote to control Sony component Select "Sony." Programming is now completed. To cancel programming Move the easy scroll key to select "Exit" or "Cancel" during any step, then press the key to enter the selection. Tips • You can freely assign any component to USER 1 and 2 items in the IR SET list 1 Do steps 1 and 2 in "Programming the Remote". 2 Move the easy scroll key to select "USER 1" or "USER 2," then press the key to enter the selection. 3 Continue from step 3 in "Programming the Remote" to select the category and maker of the component. • To operate the tuner on a Sony receiver, make sure that the tuner function's maker list is set to "Sony STR-02". 15GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Using the lists
15
GB
Programming the remote
You can customize the remote to match the
components connected to your receiver.
You
can even program the remote to control non-
Sony components and also Sony components
that the remote is normally unable to control.
The procedure below uses as an example a case
in which a Aiwa VCR is connected to the
VIDEO 2 jacks on the receiver.
Before you begin note that:
–
You cannot change the settings of TUNER and
PHONO.
–
The remote can control only components that
accept infrared wireless control signals.
Be sure to turn on the receiver and point
the remote towards the receiver when
performing the following procedure.
1
Press RM SET UP.
The set up list appears.
p
IR SET
MENU EDIT
AUTO POWER
BACK LIGHT
2
Move the easy scroll key to select “IR
SET”, then press the key to enter the
selection.
The IR SET list appears.
<IR SET>
[VIDEO 1 ]
p
[VIDEO 2 ]
[VIDEO 3 ]
3
Move the easy scroll key to select the
component (“VIDEO 2”, for example),
then press the key to enter the
selection.
The category list appears.
Category?
p
VCR
T V
L D
4
Move the easy scroll key to select the
category (i.e., the component that is
actually connected to the
corresponding jacks; in this case,
“VCR”), then press the key to enter the
selection.
The maker list appears.
Maker?
p
Sony VTR1
Sony VTR2
Sony VTR3
5
Move the easy scroll key to select the
maker of the component (“Aiwa”, for
example), then press the key to enter
the selection.
When programming the remote to
control Sony component
Select “Sony.”
Programming is now completed.
To cancel programming
Move the easy scroll key to select “Exit” or
“Cancel” during any step, then press the key to
enter the selection.
Tips
•
You can freely assign any component to USER 1
and 2 items in the IR SET list
1
Do steps 1 and 2 in “Programming the Remote”.
2
Move the easy scroll key to select “USER 1” or
“USER 2,” then press the key to enter the
selection.
3
Continue from step 3 in “Programming the
Remote” to select the category and maker of the
component.
•
To operate the tuner on a Sony receiver, make sure
that the tuner function’s maker list is set to “Sony
STR-02”.