Sony SRXT105 Installation Guide (SXRD-install) - Page 18

Connecting with Component/Video GBR Equipment, Connecting the AC Power Cord

Get Sony SRXT105 PDF manuals and user guides View all Sony SRXT105 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Chapter 2 Installation and Connections Connecting with Component/Video GBR Equipment Attach the optional LKRI-001 analog input board to the input board attachment part on the projector, and connect with a DVD recorder/player or analog video equipment equipped with the component output, or an high-definition equipment equipped with a video GBR connector. Left side INTER LOCK ETHERNET RS232C DVI-D AUX R(Pr/Cr) G(Y/Y) B(Pb/Cb) HD VD IN OUT IN OUT Connecting the AC Power Cord Use an AC power cord that supports 8AWG, 250 V, 40 A or higher. Follow the steps below to connect the three-wire power cord to the AC IN terminal on the left side of the projector. WARNING • Connection of the main power and the electric wiring work should be done by qualified electricians only. • Do not plug the power cord into the power supply before completing the following operations. 1 Remove the two screws on the terminal cover and remove it. R/Pr / G/Y / B/Pb connectors Component cable, etc (not supplied) to component output/ video GBR 2 Remove the two screws on the cable clamp and remove it. L N Betacam, DVD recorder/player, etc. Cable clamp Note When connecting to the output of HD component equipment, set "Signal Mode" of "Input Source" in the PICTURE CONTROL window to "YPbPr", and when connecting to the output of HD video GBR equipment, set to "RGB". For details, see page 25. 3 Pass the AC power cord through the hole beneath the terminal, and tighten the screw for each wire as illustrated. L N L N 18 Connecting the AC Power Cord

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
18
Connecting the AC Power Cord
Chapter 2
Installation and Connections
Connecting with Component/Video
GBR Equipment
Attach the optional LKRI-001 analog input board to the
input board attachment part on the projector, and connect
with a DVD recorder/player or analog video equipment
equipped with the component output, or an high-definition
equipment equipped with a video GBR connector.
When connecting to the output of HD component
equipment, set “Signal Mode” of “Input Source” in the
PICTURE CONTROL window to “YPbPr”, and when
connecting to the output of HD video GBR equipment, set
to “RGB”.
For details, see page 25.
Connecting the AC Power
Cord
Use an AC power cord that supports 8AWG, 250 V, 40 A
or higher.
Follow the steps below to connect the three-wire power
cord to the AC IN terminal on the left side of the projector.
•
Connection of the main power and the electric wiring
work should be done by qualified electricians only.
•
Do not plug the power cord into the power supply before
completing the following operations.
1
Remove the two screws on the terminal cover and
remove it.
2
Remove the two screws on the cable clamp and
remove it.
3
Pass the AC power cord through the hole beneath the
terminal, and tighten the screw for each wire as
illustrated.
Note
R(P
r
/C
r
)
B(P
b
/C
b
)
HD
VD
G(Y/Y)
IN
INTER LOCK
ETHERNET
RS232C
OUT
IN
OUT
AUX
DVI-D
R/P
r
/ G/Y / B/P
b
connectors
Component cable, etc
(not supplied)
Betacam, DVD recorder/player, etc.
Left side
to component output/
video GBR
WARNING
N
L
Cable clamp
N
L
N
L