Sony STR-K790 Service Manual - Page 11

Dcac Factory Test Mode - speaker setup

Get Sony STR-K790 - Lifier PDF manuals and user guides View all Sony STR-K790 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

DCAC FACTORY TEST MODE DCAC Factory Test mode have two stages: 1. DCAC DSP Data Line Checking 2. DCAC board Checking Start DSP Data Line Pass Check Auto Cal Mic Pass Check END Factory Test System Setup Receiver DCAC MIC SPK Front Left 1. When power off : Press the three buttons MUSIC + DISPLAY + ?/1 . "DCAC[]FTM" appears. Afterward, press the DIMMER to start DCAC factory test mode. 1. DCAC DSP Data Line Checking After press the DIMMER , DCAC Factory test mode will start, below display will show: "DCAC[][][]x" x = 1, 2, 3 If there is error happen, below display will show: "ERR[]SD0x" x = 1 → D1501 or R1530 x = 2 → D1502 problem x = 3 → D1503 problem 2. DCAC board Checking Connect front left speaker of the receiver and AUTO CAL microphone. Turn MASTER VOLUME jog, there will be test tone sound output from front left speaker, and the display will change accordingly. "AD[]-[]xxx" xxx = 0 to 255 (depends on loudness of test tone) STR-K790 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
11
STR-K790
DCAC FACTORY TEST MODE
DCAC Factory Test mode have two stages:
1.
DCAC DSP Data Line Checking
2.
DCAC board Checking
Factory Test System Setup
1.
When power off :
Press the three buttons
MUSIC
+
DISPLAY
+
?/1
.
“DCAC
[]
FTM” appears.
Afterward, press the
DIMMER
to start DCAC factory test
mode.
1.DCAC DSP Data Line Checking
After press the
DIMMER
, DCAC Factory test mode will start,
below display will show:
“DCAC
[][][]
x”
x = 1, 2, 3
If there is error happen, below display will show:
“ERR
[]
SD0x”
x = 1
→
D1501 or R1530
x = 2
→
D1502 problem
x = 3
→
D1503 problem
2.DCAC board Checking
Connect front left speaker of the receiver and AUTO CAL
microphone. Turn
MASTER VOLUME
jog, there will be test tone
sound output from front left speaker, and the display will change
accordingly.
“AD
[]
-
[]
xxx”
xxx = 0 to 255 (depends on loudness of test tone)
DSP Data Line
Check
Start
Pass
Pass
Auto Cal Mic
Check
END
SPK Front Left
DCAC MIC
Receiver