Sony VPL-EX275 Operating Instructions - Page 28

This mode does not work for about three minutes after the lamp lights. A change in signal may

Get Sony VPL-EX275 PDF manuals and user guides View all Sony VPL-EX275 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Notes *1: This may not be optimum depending on the input signal. In this case set manually according to the connected equipment. *2: When "Standby Mode" is set to "Low," the network and network control function cannot be operated while the projector is in standby mode. *3: This varies depending on the "Lamp Mode" setting. *4: As the lamp is dimmed gradually, you may not notice any change in brightness. You might only notice that the lamp has dimmed when its brightness is restored after there is a change in input signal. *5: This mode does not work for about three minutes after the lamp lights. A change in signal may not be detected depending on the input image. The lamp may become brighter at intervals during lamp dimming. However, this is not a malfunction. If With No Input is set, it takes priority. *6: Select "Off" to avoid entering standby mode when there is no input signal. *7: Does not function when "Type A USB", "Type B USB" or "Network" is selected as the input. In this case, it becomes equivalent to "Standard." *8: Reflecting changes in WLAN settings may take a few moments. *9: To set the IP address manually, select "Manual", press "Apply", then enter the IP address. 28 The Connection/Power Menu

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
28
The Connection/Power Menu
*1:
This may not be optimum depending on the input signal. In this case set manually according to
the connected equipment.
*2:
When “Standby Mode” is set to “Low,” the network and network control function cannot be
operated while the projector is in standby mode.
*3:
This varies depending on the “Lamp Mode” setting.
*4:
As the lamp is dimmed gradually, you may not notice any change in brightness. You might only
notice that the lamp has dimmed when its brightness is restored after there is a change in input
signal.
*5:
This mode does not work for about three minutes after the lamp lights. A change in signal may
not be detected depending on the input image. The lamp may become brighter at intervals during
lamp dimming. However, this is not a malfunction. If With No Input is set, it takes priority.
*6:
Select “Off” to avoid entering standby mode when there is no input signal.
*7:
Does not function when “Type A USB”, “Type B USB” or “Network” is selected as the input.
In this case, it becomes equivalent to “Standard.”
*8:
Reflecting changes in WLAN settings may take a few moments.
*9:
To set the IP address manually, select “Manual”, press “Apply”, then enter the IP address.
Notes