Sony VPL-FHZ57 Operating Instructions - Page 37

Off/Left-side Area/Right-side Area, HV/H/V/Off/Auto

Get Sony VPL-FHZ57 PDF manuals and user guides View all Sony VPL-FHZ57 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Setting items Description Blend Settings Configure the Edge Blending setting for the top, bottom, right, and left of the screen respectively. Left/Right/Top/Bottom: Set the Edge Blending effect for each position. Edge Blending: Set "On" to set "Blending Range" or "Blend Start Pos." Blending Range: Set the width where images are overlapped. Blend Start Pos.: Set the start position from which images are overlapped. Blend Cursor: Displays the cursors at the start and end positions for edge blending. When set to "On," the cursors are displayed during Blend settings. Start Pos. Color: Select the color of the cursor that indicates the start position. End Pos. Color: Select the color of the cursor that indicates the end position. Reset: Resets all of the Blend Settings values. Blend Fitting Finely adjusts the overlapped part. Adjust: Specify a position in the overlapped area and move image pixels. Use V/v/B/b to select the position to adjust. Press the ENTER key to determine the position and use V/v/B/b to move the image pixels vertically/horizontally so that neighboring images overlap. Reset: Resets all of the Blend Fitting values. Zone Black Level Adj.*4 *5 *6 Adjusts so that the overlapped part is not noticeably bright when a dark image is displayed. Select the correction zone "Adjust Zone 1" through "Adjust Zone 9," and set the adjustment values. Zone Fitting: Adjusts the area of each correction zone. Adjust: Specifies the position of the marginal line of each correction zone. Select the adjusting position using V/v/B/b. Press the ENTER key to determine the position and use V/v/B/b to move the image pixels vertically/horizontally so that the area of each correction zone is adjusted. Reset: Resets all of the Zone Fitting values. Black Level Adj.: Adjusts the brightness of each correction zone. Reset: Resets all of the Black Level Adj. values. Reset: Resets all of the Zone Black Level Adj. values. Image Split Off/Left-side Area/Right-side Area: Divides the input signal from the computer in half, and displays an enlarged image of the left-side or right-side area on the screen.*7 Image Flip HV/H/V/Off/Auto: Flips the projected image horizontally and/or vertically according to the installation method. High Altitude Mode On/Off: Set to "On" when using the projector at an altitude of 1,500 m or higher. Continuing to use the wrong setting may affect component reliability. Filter Cleaning Turns off the projector and cleans the air filter.*8 Filter Box (Op) Installed/Not Installed: Set to "Installed" when using Projector Filter Box (PK-F60FB1.) Screen Aspect 16:10/16:9/4:3: For switching the display area to suit to the screen. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
37
Blend
Settings
Configure the Edge Blending setting for the top, bottom, right, and left of
the screen respectively.
Left/Right/Top/Bottom:
Set the Edge Blending effect for each position.
Edge Blending:
Set “On” to set “Blending Range” or “Blend Start Pos.”
Blending Range:
Set the width where images are overlapped.
Blend Start Pos.:
Set the start position from which images are
overlapped.
Blend Cursor:
Displays the cursors at the start and end positions for edge
blending. When set to “On,” the cursors are displayed during Blend
settings.
Start Pos. Color:
Select the color of the cursor that indicates the start
position.
End Pos. Color:
Select the color of the cursor that indicates the end
position.
Reset:
Resets all of the Blend Settings values.
Blend Fitting
Finely adjusts the overlapped part.
Adjust:
Specify a position in the overlapped area and move image pixels.
Use
V
/
v
/
B
/
b
to select the position to adjust. Press the ENTER key to
determine the position and use
V
/
v
/
B
/
b
to move the image pixels
vertically/horizontally so that neighboring images overlap.
Reset:
Resets all of the Blend Fitting values.
Zone Black
Level Adj.
*4
*5 *6
Adjusts so that the overlapped part is not noticeably bright when a dark
image is displayed.
Select the correction zone “Adjust Zone 1” through “Adjust Zone 9,” and
set the adjustment values.
Zone Fitting:
Adjusts the area of each correction zone.
Adjust:
Specifies the position of the marginal line of each correction
zone.
Select the adjusting position using
V
/
v
/
B
/
b
. Press the ENTER key to
determine the position and use
V
/
v
/
B
/
b
to move the image pixels
vertically/horizontally so that the area of each correction zone is adjusted.
Reset:
Resets all of the Zone Fitting values.
Black Level Adj.:
Adjusts the brightness of each correction zone.
Reset:
Resets all of the Black Level Adj. values.
Reset:
Resets all of the Zone Black Level Adj. values.
Image Split
Off/Left-side Area/Right-side Area:
Divides the input signal from the
computer in half, and displays an enlarged image of the left-side or right-side
area on the screen.
*7
Image Flip
HV/H/V/Off/Auto:
Flips the projected image horizontally and/or
vertically according to the installation method.
High Altitude Mode
On/Off:
Set to “On” when using the projector at an altitude of 1,500 m or
higher. Continuing to use the wrong setting may affect component
reliability.
Filter Cleaning
Turns off the projector and cleans the air filter.
*8
Filter Box (Op)
Installed/Not Installed:
Set to “Installed” when using Projector Filter Box
(PK-F60FB1.)
Screen Aspect
16:10/16:9/4:3:
For switching the display area to suit to the screen.
Setting items
Description