Sony VPL-VW760ES Operating Instructions - Page 35

Remote control, 3D video images, Others, Symptom, Cause and Remedy

Get Sony VPL-VW760ES PDF manuals and user guides View all Sony VPL-VW760ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Remote control Symptom The remote control does not work. 3D video images Cause and Remedy Batteries could be weak. Replace them with new batteries. Insert the batteries with the correct polarities. If there is a fluorescent lamp near the remote control detector, the unit may work improperly or inadvertently. Confirm the position of the remote control detector on the unit. Set "IR Receiver" to "Front & Rear" on the Installation menu. Make sure that the cable is not connected to the IR IN connector. Page - - - 3, 4 29 3 Symptom The video image does not seem like 3D video images. Cause and Remedy Check if the 3D glasses are turned on. Make sure that the battery in the 3D glasses is sufficiently charged. Set "2D-3D Display Sel." to "Auto" or "3D." Check if the input signals are compatible 3D signals. The 3D signals may not be input depending on the specifications of the connected AV selector/AV amplifier/external equipment. If the 3D signal is not input, confirm the specifications and/or settings of the AV selector/AV amplifier/external equipment. When the viewing position is too far from the unit, the 3D glasses may not be able to display the images properly. The screen size is not appropriate. Set the zooming magnification to low or watch the image from farther away from the screen. For details, see "Precautions for use" of "Using the 3D Glasses." Others Page 12 - 26 42 - 12 47 12 Symptom The fan is noisy. The lens shift cannot be adjusted. Cause and Remedy Page Check the setting of "High Altitude Mode" on the Setup menu. 25 Make sure that the room temperature is not too high. - Check the installation requirements of the unit. - Fan speed increases to maintain the product reliability of the projector's components in a room where the temperature is higher than normal. The fan noise becomes slightly louder in these rooms. The approximate normal temperature for the unit is 25°C (77°F). The lens shift cannot be adjusted over the range of movement. Adjust the lens shift within 8, 47 the range of movement. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
35
Remote control
3D video images
Others
Symptom
Cause and Remedy
Page
The remote control does not work.
Batteries could be weak. Replace them with new batteries.
–
Insert the batteries with the correct polarities.
–
If there is a fluorescent lamp near the remote control detector, the unit may work
improperly or inadvertently.
–
Confirm the position of the remote control detector on the unit.
3, 4
Set “IR Receiver” to “Front & Rear” on the Installation
menu.
29
Make sure that the cable is not connected to the IR IN connector.
3
Symptom
Cause and Remedy
Page
The video image does not seem like
3D video images.
Check if the 3D glasses are turned on.
12
Make sure that the battery in the 3D glasses is sufficiently charged.
–
Set “2D-3D Display Sel.” to “Auto” or “3D.”
26
Check if the input signals are compatible 3D signals.
42
The 3D signals may not be input depending on the specifications of the connected AV
selector/AV amplifier/external equipment. If the 3D signal is not input, confirm the
specifications and/or settings of the AV selector/AV amplifier/external equipment.
–
When the viewing position is too far from the unit, the 3D glasses may not be able to
display the images properly.
12
The screen size is not appropriate. Set the zooming magnification to low or watch the
image from farther away from the screen.
47
For details, see “Precautions for use” of “Using the 3D Glasses.”
12
Symptom
Cause and Remedy
Page
The fan is noisy.
Check the setting of “High Altitude Mode” on the Setup
menu.
25
Make sure that the room temperature is not too high.
–
Check the installation requirements of the unit.
Fan speed increases to maintain the product reliability of the projector’s components in a
room where the temperature is higher than normal. The fan noise becomes slightly louder
in these rooms. The approximate normal temperature for the unit is 25°C (77°F).
–
The lens shift cannot be adjusted.
The lens shift cannot be adjusted over the range of movement. Adjust the lens shift within
the range of movement.
8, 47