Stihl SR 200 Product Instruction Manual - Page 14

Assembling the Unit - owners manual

Page 14 highlights

2431BA002 KN English In California, it is a violation of § 4442 or § 4443 of the Public Resources Code to use or operate gasoline-powered tools on forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a complying spark arrester that is maintained in effective working order. The owner/operator of this product is responsible for properly maintaining the spark arrester. Other states or governmental entities/agencies, such as the U.S. Forest Service, may have similar requirements. Contact your local fire agency or forest service for the laws or regulations relating to fire protection requirements. Tighten all nuts, bolts and screws except the carburetor adjustment screws after each use. For maintenance items please also refer to the maintenance chart in this instruction manual. Store the power tool in a dry and high or locked location out of reach of children. Before storing for longer than a few days, always empty the fuel tank. See chapter "Storing the machine" in this instruction manual. Store fuel in an approved and properly labeled safety-type canister only. Take care when handling gasoline! For health and safety reasons, avoid direct contact with the skin and avoid inhaling fuel vapor! Assembling the Unit NOTICE The solution hose and throttle cable are already connected and must not be kinked while assembling the machine. The combination wrench and screwdriver are in the supplied accessory bag. Fitting the pleated hose on the elbow 1 2 N Open the hose clamp (1) and fit it on the pleated hose (2). N Engage the tab in the recess. 3 2 2431BA017 KN N Push the pleated hose (2) over the slip ring (3) as far as stop. 9928BA001 AM 31 N Line up the hose clamp (1) and slip ring (3): - the two lugs (arrow) on the slip ring face up. - The hose clamp's hook faces outwards. N Tighten down the screw (arrow). Mounting the Control Handle 2 3 1 N Open up the control handle (1) with liner (2) and push it over the stub (3) of the pleated hose. 9928BA019 AM 2431BA003 KN 12 SR 200

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84

SR 200
English
12
In California, it is a violation of § 4442 or
§ 4443 of the Public Resources Code to
use or operate gasoline-powered tools
on forest-covered, brush-covered or
grass-covered land unless the engine’s
exhaust system is equipped with a
complying spark arrester that is
maintained in effective working order.
The owner/operator of this product is
responsible for properly maintaining the
spark arrester. Other states or
governmental entities/agencies, such as
the U.S. Forest Service, may have
similar requirements. Contact your local
fire agency or forest service for the laws
or regulations relating to fire protection
requirements.
Tighten all nuts, bolts and screws except
the carburetor adjustment screws after
each use.
For maintenance items please also refer
to the maintenance chart in this
instruction manual.
Store the power tool in a dry and high or
locked location out of reach of children.
Before storing for longer than a few
days, always empty the fuel tank. See
chapter "Storing the machine" in this
instruction manual.
Store fuel in an approved and properly
labeled safety-type canister only. Take
care when handling gasoline! For health
and safety reasons, avoid direct contact
with the skin and avoid inhaling fuel
vapor!
NOTICE
The solution hose and throttle cable are
already connected and must not be
kinked while assembling the machine.
The combination wrench and
screwdriver are in the supplied
accessory bag.
Fitting the pleated hose on the elbow
N
Open the hose clamp
(1) and fit it on
the pleated hose (2).
N
Engage the tab in the recess.
N
Push the pleated hose (2) over the
slip ring (3) as far as stop.
N
Line up the hose clamp (1) and slip
ring (3):
the two lugs (arrow) on the slip ring
face up.
The hose clamp's hook faces
outwards.
N
Tighten down the screw (arrow).
Mounting the Control Handle
N
Open up the control handle (1) with
liner
(2) and push it over the stub
(3)
of the pleated hose.
Assembling the Unit
1
2
9928BA001 AM
3
2
2431BA017 KN
3
1
2431BA002 KN
9928BA019 AM
3
2431BA003 KN
1
2