Sub-Zero BI-36S Sub-Zero Design Guide - Page 34

Flush Inset Panel Offsets

Get Sub-Zero BI-36S PDF manuals and user guides View all Sub-Zero BI-36S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Built-In Refrigeration 34 Dual Installation FLUSH INSET PANEL OFFSETS When installing two built-in models side by side in a flush inset application, you must decrease the width of the decorative flush inset panels by 1/2" (13). Adjustments to the panel offsets will also need to be made. These adjustments are needed to achieve a proper fit and to ensure the panels do not collide when closing. Panel dimensions in the chart below have been adjusted to reflect the decrease in panel dimensions. IMPORTANT NOTE: If a filler strip is not used, dual installations can only be accomplished using two units with opposite hinges. Illustrations A-F provide panel offsets and reveals for all built-in models in a flush inset application. Refer to the chart below for reference to the illustrations relating to your specific model. All reveals are 1/2" (13) unless otherwise specified. For additional information on model-specific panel reveals, visit the specification library section of our website, subzerotrade.com. Do not exceed flush inset panel dimensions, as this could cause damage to panels and the Sub-Zero unit. Panel Offsets ALL REFRIGERATOR / ALL FREEZER Doors (hinge) / Grille Sides Doors (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom OVER-AND-UNDER Doors (hinge) / Drawer / Grille Sides Doors (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom / Drawer Top Drawer Bottom Illus. A B C D F A B C D E F TOP VIEW DOOR / DRAWER / GRILLE BACKER SPACER CABINETRY DOOR TOP VIEW DUAL TRIM DOOR FLUSH INSET PANEL 5/16" (8) 1/2" (13) 5/8" (16) 5/16" (8) 1/8" (3) 1/4" (6) REVEAL Illus. A Illus. B CABINETRY 1/2" (13) GRILLE 1/8" 5/16" (3) (8) GRILLE DOOR Illus. C SIDE VIEW Illus. D 5/16" (8) 5/32" (4) 1/2" (13) 3/32" 5/16" (2) (8) SIDE VIEW DOOR DRAWER Illus. E 5/16" (8) 3/32" (2) 5/8" (16) 5/32" 5/16" (4) (8) SIDE VIEW DOOR / DRAWER 5/16" (8) SIDE VIEW 3/32" (2) Illus. F

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Built-In Refrigeration
34
Dual Installation
FLUSH INSET PANEL OFFSETS
When installing two built-in models side by side in a flush
inset application, you must decrease the width of the dec-
orative flush inset panels by
1
/
2
"
(13)
. Adjustments to the
panel offsets will also need to be made. These adjust-
ments are needed to achieve a proper fit and to ensure the
panels do not collide when closing. Panel dimensions in
the chart below have been adjusted to reflect the
decrease in panel dimensions.
IMPORTANT NOTE:
If a filler strip is not used, dual instal-
lations can only be accomplished using two units with
opposite hinges.
Illustrations A–F provide panel offsets and reveals for all
built-in models in a flush inset application. Refer to the
chart below for reference to the illustrations relating to
your specific model. All reveals are
1
/
2
"
(13)
unless other-
wise specified.
For additional information on model-specific panel reveals,
visit the specification library section of our website,
subzerotrade.com.
5
/
8
"
(16)
5
/
16
"
(8)
1
/
2
"
(13)
FLUSH INSET PANEL
SPACER
BACKER
DOOR / DRAWER / GRILLE
TOP VIEW
CABINETRY
Illus. A
Illus. B
DUAL
TRIM
1
/
4
"
(6)
REVEAL
5
/
16
"
(8)
1
/
8
"
(3)
DOOR
DOOR
TOP VIEW
1
/
2
"
(13)
5
/
16
"
(8)
1
/
8
"
(3)
CABINETRY
GRILLE
SIDE VIEW
Illus. C
Illus. D
1
/
2
"
(13)
3
/
32
"
(2)
5
/
16
"
(8)
5
/
16
"
(8)
5
/
32
"
(4)
GRILLE
DOOR
SIDE VIEW
5
/
8
"
(16)
5
/
32
"
(4)
5
/
16
"
(8)
5
/
16
"
(8)
3
/
32
"
(2)
DOOR
DRAWER
SIDE VIEW
Illus. E
Illus. F
5
/
16
"
(8)
3
/
32
"
(2)
DOOR /
DRAWER
SIDE VIEW
Panel Offsets
Illus.
ALL REFRIGERATOR / ALL FREEZER
Doors (hinge) / Grille Sides
A
Doors (handle) Sides
B
Grille Top
C
Grille Bottom / Door Top
D
Door Bottom
F
OVER-AND-UNDER
Doors (hinge) / Drawer / Grille Sides
A
Doors (handle) Sides
B
Grille Top
C
Grille Bottom / Door Top
D
Door Bottom / Drawer Top
E
Drawer Bottom
F
Do not exceed flush inset panel dimensions, as this
could cause damage to panels and the Sub-Zero unit.