Sub-Zero BI-36S Built-In Use & Care Guide - Page 28

Cleaning, Built-In Use & Care

Get Sub-Zero BI-36S PDF manuals and user guides View all Sub-Zero BI-36S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Built-In Use & Care 28 Cleaning INTERIOR CLEANING To clean interior surfaces, the water grille for internal dispenser models and all other removable parts, wash with a mild solution of soap and lukewarm water with a little baking soda. Rinse and dry thoroughly. Avoid getting water on lights and the control panel. When cleaning an over-and-under or side-by-side model, it is possible to turn off one section of the combination unit for an extended period without disrupting operation of the other. First, turn the unit off. Press and hold the WARMER key pad of the section you want to disable. While holding the WARMER key pad, press the POWER key pad. Then, release both key pads. The disabled section will appear blank in the control panel display. Refer to the illustration below. Repeat the process to turn the section back on. Refer to electronic control system on page 14. GLASSWELL CLEANING To clean the glasswell of external dispenser models BI-42SD and BI-48SD, use a mild solution of soap and water with a little baking soda. Remove the dispenser water grille to wipe up any spills. To remove the water grille, press down on the front left corner of the grille and lift it out. For the stainless steel areas of the glasswell, refer to stainless steel exterior cleaning on the following page. Do not use vinegar, rubbing alcohol or other alcoholbased cleaners on any interior surface. Do not submerge or pour hot water over cold glass shelves. CONTROL PANEL DISPLAY Control panel display.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Cleaning
INTERIOR CLEANING
To clean interior surfaces, the water grille for internal
dispenser models and all other removable parts, wash
with a mild solution of soap and lukewarm water with a
little baking soda. Rinse and dry thoroughly. Avoid getting
water on lights and the control panel.
When cleaning an over-and-under or side-by-side model,
it is possible to turn off one section of the combination
unit for an extended period without disrupting operation
of the other.
First, turn the unit off. Press and hold the WARMER key
pad of the section you want to disable. While holding the
WARMER key pad, press the POWER key pad. Then,
release both key pads. The disabled section will appear
blank in the control panel display. Refer to the illustration
below. Repeat the process to turn the section back on.
Refer to electronic control system on page 14.
Built-In Use & Care
28
GLASSWELL CLEANING
To clean the glasswell of external dispenser models
BI-42SD and BI-48SD, use a mild solution of soap and
water with a little baking soda. Remove the dispenser
water grille to wipe up any spills. To remove the water
grille, press down on the front left corner of the grille and
lift it out. For the stainless steel areas of the glasswell,
refer to stainless steel exterior cleaning on the following
page.
Do not use vinegar, rubbing alcohol or other alcohol-
based cleaners on any interior surface.
Do not submerge or pour hot water over cold glass
shelves.
CONTROL PANEL
DISPLAY
Control panel display.