TASCAM DA-6400 DA-6400dp Owners Manual Addendum V3.10 - Page 35

New functions in firmware version 1.40, TASCAM IF-AN16/OUT analog output interface card support added

Get TASCAM DA-6400 PDF manuals and user guides View all TASCAM DA-6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

DA-6400/DA-6400dp New functions in firmware version 1.40 The following new functions have been added in firmware version 1.40. o The TASCAM IF-AN16/OUT analog output interface card is now supported. TASCAM IF-AN16/OUT analog output interface card support added The TASCAM IF-AN16/OUT analog output interface card is now supported. If installed in SLOT 1 or SLOT 2 of this unit, the following appears on the SLOT1 or SLOT2 menu page. Adjusting output levels You can adjust the output levels of the IF-AN16/OUT to suit the connected devices. All 16 channels can be adjusted individually or together. 1. Select the SLOT 1 or SLOT 2 menu page OUTPUT ATTENUATOR item, and press the MULTI JOG dial to open the OUTPUT ATTENUATOR settings list for that slot. NOTE i The IF-AN16/OUT cannot be set as this unit's master clock. If you try to set it, the following pop-up message will appear. [SLOT 2 page] i If an IF-AN16/OUT is installed, replacing a slot card, or SYSTEM BACKUP settings are imported, the IF-AN16/OUT could become set improperly as the master clock. If this occurs, the master clock setting will automatically be switched to Internal and the INFO indicator will light red. In this state, the following message will appear if you open the INFORMATION screen. After confirming this message once, it will not appear again. [OUTPUT ATTENUATOR setting list] 2. Turn the MULTI JOG dial to select the channel you want to adjust, and press the MULTI JOG dial to open the OUTPUT ATTENUATOR setting adjustment screen. i If an input signal is assigned for the slot in which the IF-AN16/ OUT is installed and the PREFERENCES page NO SIGNAL ERROR CHECK item is set to ON, the INFO indicator will light red and a message like "SLOT 1 has no signal" will appear on an ERROR INFORMATION screen. If you do not want such error messages to appear, set the PREFERENCES page NO SIGNAL ERROR CHECK item to OFF. [OUTPUT ATTENUATOR setting adjustment screen] 3. Select the EDIT MODE item, and turn the MULTI JOG dial to set how the values are changed. Press the MULTI JOG dial to move the cursor to the next item. You can also use the . and / buttons to move the cursor. Option Individual (default) ALL BATCH SETUP Meaning Change settings for 1 channel at a time. Change settings for all 16 channels at the same time. Change settings for multiple designated channels at the same time. TASCAM DA-6400/DA-6400dp 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
New functions in firmware version 1.40
The following new functions have been added in firmware version 1.40.
o
The TASCAM IF-AN16/OUT analog output interface card is now supported.
TASCAM IF-AN16/OUT analog output interface card support added
The TASCAM IF-AN16/OUT analog output interface card is now
supported.
If installed in
SLOT 1
or
SLOT 2
of this unit, the following
appears on the
SLOT1
or
SLOT2
menu page.
NOTE
i
The IF-AN16/OUT cannot be set as this unit's master clock. If
you try to set it, the following pop-up message will appear.
i
If an IF-AN16/OUT is installed, replacing a slot card, or
SYSTEM BACKUP
settings are imported, the IF-AN16/OUT
could become set improperly as the master clock.
If this occurs, the master clock setting will automatically be
switched to
Internal
and the INFO indicator will light red.
In this state, the following message will appear if you open
the
INFORMATION
screen. After confirming this message
once, it will not appear again.
i
If an input signal is assigned for the slot in which the IF-AN16/
OUT is installed and the
PREFERENCES
page
NO SIGNAL
ERROR CHECK
item is set to
ON
, the INFO indicator will light
red and a message like “
SLOT 1 has no signal
” will
appear on an
ERROR INFORMATION
screen.
If you do not want such error messages to appear, set the
PREFERENCES
page
NO SIGNAL ERROR CHECK
item to
OFF
.
Adjusting output levels
You can adjust the output levels of the IF-AN16/OUT to suit the
connected devices. All 16 channels can be adjusted individually
or together.
1.
Select the
SLOT 1
or
SLOT 2
menu page
OUTPUT
ATTENUATOR
item, and press the
MULTI JOG
dial to open
the
OUTPUT ATTENUATOR
settings list for that slot.
[SLOT 2 page]
[OUTPUT ATTENUATOR setting list]
2.
Turn the
MULTI JOG
dial to select the channel you want to
adjust, and press the
MULTI JOG
dial to open the OUTPUT
ATTENUATOR setting adjustment screen.
[OUTPUT ATTENUATOR setting adjustment screen]
3.
Select the
EDIT MODE
item, and turn the MULTI JOG dial to
set how the values are changed.
Press the MULTI JOG dial to move the cursor to the next
item. You can also use the . and / buttons to move the
cursor.
Option
Meaning
Individual
(default)
Change settings for 1 channel at a
time.
ALL
Change settings for all 16 channels
at the same time.
BATCH SETUP
Change settings for multiple
designated channels at the same
time.
TASCAM
DA-6400/DA-6400dp
35
DA-6400/DA-6400dp