TASCAM DM-24 Downloads Update Instructions - Page 15

INITIALIZATION PROCESS, start.mid Main CPU StartUp Program Data - factory reset

Get TASCAM DM-24 PDF manuals and user guides View all TASCAM DM-24 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

12. Now repeat these steps to load the next six files. These files must be loaded in the following order or damage will be done to your DM-24's EPROMs and the DM-24 will be unusable: 2. remote.mid (Remote Program Data) 3. main.mid (Main CPU Program Data) 4. preset.mid (Preset Library Data) * 5. diag.mid (Diagnostics Program Data) * 6. start.mid (Main CPU StartUp Program Data) * 7. panel.mid (Panel CPU Program Data) 13. Once these files have been loaded, press SHIFT+OPTION on the DM-24. 14. Press the soft key below where you see PREFERENCES on the LCD. 15. Use the cursor keys to point to VERSION INFO. You will see a list of different files. All of them should be labeled with the upgraded version you just loaded. 16. Once finished, you will need to initialize your DM-24. Please see the end of this document for that procedure. INITIALIZATION PROCESS 1. With the power OFF hold down the 2nd F button (far left of the board), the HIGH button (just above in the EQ section) and the - button (just to the right in the LIBRARY section) while you turn the power ON. 2. The DM-24 will boot to DIAGNOSTIC MODE. As soon as you see DIAGNOSTIC MODE on the display you may release the 2nd F, HIGH and - buttons. 3. Use the "Down cursor key" to move the indicator to SRAM INIT (NOT SRAM INIT for factory TEST) and press ENTER. 4. Press ENTER again to confirm when prompted. A check mark will appear in the box next to SRAM INIT on the display. 5. Use the "Down cursor key" to move the indicator to FLASH INFORMATION CLEAR and press ENTER. 6. Press ENTER again to confirm when prompted. A check mark will appear in the box next to FLASH INFORMATION CLEAR on the display. 7. Use the "Down cursor key" to move the indicator to EXIT and press ENTER. This will reset the DM-24 back to the original factory settings and the DM-24 will reboot.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
12.
Now repeat these steps to load the next six files.
These files must be loaded in the following order or
damage will be done to your DM-24’s EPROMs and the DM-24 will be unusable:
2. remote.mid (Remote Program Data)
3. main.mid (Main CPU Program Data)
4. preset.mid (Preset Library Data) *
5. diag.mid (Diagnostics Program Data) *
6. start.mid (Main CPU StartUp Program Data) *
7. panel.mid (Panel CPU Program Data)
13.
Once these files have been loaded, press SHIFT+OPTION on the DM-24.
14.
Press the soft key below where you see PREFERENCES on the LCD.
15.
Use the cursor keys to point to VERSION INFO.
You will see a list of different files.
All of them
should be labeled with the upgraded version you just loaded.
16.
Once finished, you will need to initialize your DM-24.
Please see the end of this document for that
procedure.
INITIALIZATION PROCESS
1.
With the power OFF hold down the 2nd F button (far left of the board), the HIGH button (just
above in the EQ section) and the – button (just to the right in the LIBRARY section) while you turn
the power ON.
2.
The DM-24 will boot to DIAGNOSTIC MODE.
As soon as you see DIAGNOSTIC MODE on the
display you may release the 2nd F, HIGH and – buttons.
3.
Use the “Down cursor key” to move the indicator to SRAM INIT (NOT SRAM INIT for factory
TEST) and press ENTER.
4.
Press ENTER again to confirm when prompted.
A check mark will appear in the box next to
SRAM INIT on the display.
5.
Use the “Down cursor key” to move the indicator to FLASH INFORMATION CLEAR and press
ENTER.
6.
Press ENTER again to confirm when prompted.
A check mark will appear in the box next to
FLASH INFORMATION CLEAR on the display.
7.
Use the “Down cursor key” to move the indicator to EXIT and press ENTER.
This will reset the
DM-24 back to the original factory settings and the DM-24 will reboot.