TP-Link Archer VR900 Archer VR900 V1 User Guide - Page 83

Create Static Routes, Wi-Fi 2.4G, Enable Group Isolation, For example

Get TP-Link Archer VR900 PDF manuals and user guides View all TP-Link Archer VR900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Chapter 12 Specify Your Network Settings Done! 5. Check the boxes of LAN1 and LAN3 in Available LAN. Here Wi-Fi 2.4G network and Wi-Fi 5G network are viewed as a LAN interface respectively. 6. Click Enable Group Isolation to isolate working devices and disallow other devices from communicating with them. 7. Click OK to save the settings. Now your working devices connected to LAN1 and LAN3 are in an isolated group! Note: VLAN function is enabled by default. You cannot disable it when IPTV is enabled. 12. 5. Create Static Routes A static route is a pre-determined path that network information must travel to reach a specific host or network. Data from one point to another will always follow the same path regardless of other considerations. Normal Internet usage does not require this setting to be configured. I want to: Visit multiple networks and multiple servers at the same time. For example, in a small office, my PC can surf the Internet, but I also want to visit my company's server. Now I have a switch and another router. I connect the devices as shown in the following figure so that the physical connection between my PC and my company's server is achieved. To surf the Internet and visit my company's network at the same time, I need to configure the static routing. Modem router Router 2 Company's server LAN: 192.168.1.1 WAN: 172.30.30.100 LAN: 192.168.1.2 172.30.30.1 Switch How can I do that? 192.168.1.100 My PC 1. Make sure the routers use different LAN IP addresses on the same subnet. Disable Router 2's DHCP function. 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
79
Chapter 12
Specify Your Network Settings
5°
Check the boxes of
LAN1
and
LAN3
in Available LAN. Here
Wi-Fi 2.4G
network and
Wi-Fi 5G
network are viewed as a
LAN interface respectively.
6°
Click
Enable Group Isolation
to isolate working devices and
disallow other devices from communicating with them.
7°
Click
OK
to save the settings.
Now your working devices connected to LAN1 and LAN3 are in
an isolated group!
Note:
VLAN function is enabled by default. You cannot disable it when IPTV is
enabled.
12° 5°
Create Static Routes
A static route is a pre-determined path that network information must travel to reach
a specific host or network. Data from one point to another will always follow the same
path regardless of other considerations. Normal Internet usage does not require this
setting to be configured.
Visit multiple networks and multiple servers at the same time.
For example
, in a small office, my PC can surf the Internet, but I
also want to visit my company’s server. Now I have a switch and
another router. I connect the devices as shown in the following
figure so that the physical connection between my PC and my
company’s server is achieved. To surf the Internet and visit my
company’s network at the same time, I need to configure the
static routing.
Company’s server
My PC
Router 2
Modem router
Switch
LAN: 192.168.1.1
192.168.1.100
LAN: 192.168.1.2
WAN: 172.30.30.100
172.30.30.1
1°
Make sure the routers use different LAN IP addresses on the
same subnet. Disable Router 2’s DHCP function.
Done!
I want to:
How can I
do that?