Toshiba NB555D PLL5FC-011013 Users Manual Canada; English - Page 56

Installing a memory module, note that the screws are attached to the cover in order to prevent them

Get Toshiba NB555D PLL5FC-011013 PDF manuals and user guides View all Toshiba NB555D PLL5FC-011013 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

NB500/NB505/NB520/NB525/NB550D/NB555D Series Use a point size 0 Phillips screwdriver to remove and fasten the screws the use of an incorrect screwdriver can damage the screw heads. Installing a memory module To install a memory module, follow the steps as detailed below: 1. Shut down the computer - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started if required). 2. Remove the AC adaptor and all cables and peripherals connected to the computer. 3. Close the display panel. 4. Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section in Chapter 5, Power and Power-Up Modes, if required). 5. Loosen the screws securing the memory module cover in place - please note that the screws are attached to the cover in order to prevent them from being lost. Use a point size 0 Phillips screwdriver. 6. Slide your fingernail or a thin object under the cover and lift it off. Figure 3-7 Removing the memory module cover 1 1 2 1. Screws 2. Memory module cover 7. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place. User's Manual 3-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
User’s Manual
3-19
NB500/NB505/NB520/NB525/NB550D/NB555D Series
Installing a memory module
To install a memory module, follow the steps as detailed below:
1.
Shut down the computer - make sure the Power indicator is off (refer to
the
Turning off the power
section in Chapter 1, Getting Started if
required).
2.
Remove the AC adaptor and all cables and peripherals connected to
the computer.
3.
Close the display panel.
4.
Turn the computer upside down and remove the battery pack (refer to
Replacing the battery pack
section in Chapter 5, Power and Power-Up
Modes, if required).
5.
Loosen the screws securing the memory module cover in place - please
note that the screws are attached to the cover in order to prevent them
from being lost.
6.
Slide your fingernail or a thin object under the cover and lift it off.
Figure 3-7 Removing the memory module cover
7.
Align the notch of the memory module with that of the memory slot and
gently insert the module into the slot at about a 30 degree angle before
holding it down until the latches on either side snap into place.
Use a point size 0 Phillips screwdriver to remove and fasten the screws -
the use of an incorrect screwdriver can damage the screw heads.
Use a point size 0 Phillips screwdriver.
1. Screws
2. Memory module cover
2
1
1