Toshiba Satellite P25-S609 User Guide - Page 236

The system does not recognize your PC Card or, PCMCIA socket controller., A PC Card error occurs.

Page 236 highlights

236 If Something Goes Wrong Resolving a hardware conflict 2 Click Stop xxxx, where xxxx is the identifier for your PC Card. The operating system displays a message that you may safely remove the card. 3 Remove the card from the slot. Never swap modules when the computer is in Hibernation or Stand By mode. This is known as "warm swapping" and is not supported with this computer. For more information on Hibernation and Stand By modes, see "Hibernation command" on page 94 and "Stand By command" on page 95. The system does not recognize your PC Card or PCMCIA socket controller. 1 Make sure the computer is not in Stand By mode. For more information, see "Using Stand By" on page 99. 2 Turn off the computer. 3 Connect the AC adapter and power cable. 4 Keep the computer plugged in for about three hours with the power turned off. The problem may also be caused by a conflict with any additional memory in your system. Removing a malfunctioning card and reinstalling it can correct many problems. For more information, see "Inserting PC Cards" on page 212. A PC Card error occurs. Reinsert the card to make sure it is properly connected. If the card is attached to an external device, check that the connection is secure. Refer to the card's documentation, which should contain a troubleshooting section.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278

236
If Something Goes Wrong
Resolving a hardware conflict
2
Click
Stop
xxxx
, where
xxxx
is the identifier for your PC
Card.
The operating system displays a message that you may
safely remove the card.
3
Remove the card from the slot.
Never swap modules when the computer is in Hibernation or
Stand By mode. This is known as “warm swapping” and is not
supported with this computer. For more information on
Hibernation and Stand By modes, see
“Hibernation command”
on page 94
and
“Stand By command” on page 95
.
The system does not recognize your PC Card or
PCMCIA socket controller.
1
Make sure the computer is not in Stand By mode. For
more information, see
“Using Stand By” on page 99
.
2
Turn off the computer.
3
Connect the AC adapter and power cable.
4
Keep the computer plugged in for about three hours with
the power turned off.
The problem may also be caused by a conflict with any
additional memory in your system.
Removing a malfunctioning card and reinstalling it can
correct many problems. For more information, see
“Inserting
PC Cards” on page 212
.
A PC Card error occurs.
Reinsert the card to make sure it is properly connected.
If the card is attached to an external device, check that the
connection is secure.
Refer to the card’s documentation, which should contain a
troubleshooting section.