Via EPIA-5000 User Manual - Page 21

Connectors - a

Get Via EPIA-5000 - VIA Motherboard - Mini ITX PDF manuals and user guides View all Via EPIA-5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Hardware Setup Connectors The VIA EPIA Mini-ITX Mainboard provides the following connectors: IDE Connectors The two PCI IDE connectors (IDE 1 & IDE 2) support Ultra DMA 33/66/ 100 modes. IDE 1 is the primary IDE connector and IDE 2 is the secondary IDE connector. Both IDE 1 and IDE2 can connect a master and a slave drive, allowing a maximum of four seperate devices, such as a HDD, CDROM or CD-RW, to be connected. Also, a Disk on Module can be connected directly to one of the IDE connectors. These connectors utilize the provided IDE cable. IDE 1 IDE 2 NB: If you install two HDDs on one IDE cable, you must set the second drive to slave mode by setting its jumper on the HDD. Please refer to the HDD documentation supplied by the HDD vendor for correct jumper setiing instructions. 2-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Hardware Setup
2-9
The VIA EPIA Mini-ITX Mainboard provides the following connectors:
IDE Connectors
The two PCI IDE connectors (IDE 1 & IDE 2) support Ultra DMA 33/66/
100 modes. IDE 1 is the primary IDE connector and IDE 2 is the secondary
IDE connector. Both IDE 1 and IDE2 can connect a master and a slave
drive, allowing a maximum of four seperate devices, such as a HDD, CD-
ROM or CD-RW, to be connected.
Also, a Disk on Module can be connected directly to one of the IDE
connectors.
These connectors utilize the provided IDE cable.
Connectors
IDE 1
IDE 2
NB:
If you install two HDDs on one IDE cable, you must set
the second drive to
slave
mode by setting its jumper on the
HDD. Please refer to the HDD documentation supplied by the
HDD vendor for correct jumper setiing instructions.