ViewSonic LS700-4K User Guide - Page 24

Operation, Activate the projector

Get ViewSonic LS700-4K PDF manuals and user guides View all ViewSonic LS700-4K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Operation Activate the projector Plug the power cord into the projector and into a wall socket. Turn on the switch on the wall socket (if available). Press Power to switch on the projector. If this is the first time that you've switched on the projector, please refer to on-screen instructions and select your OSD language and Projection mode. Switch on all connected equipment. The projector will then begin a search of the input signals. The options indicating green light dots are the signal sources currently available. If the projector fails to detect a valid signal, the screen will display a [NO SIGNAL] message until an input signal is found. You can also press the [Source] key or the shortcut key on the remote control to select the desired input signals. Please refer to "Switching input signal" for the details. If the input signal frequency / resolution is outside the operating range of the projector, the blank screen will display the [Out of Range] message. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. For more details, please refer to the "Timing chart". 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
17
Operation
Activate the projector
Plug the power cord into the projector and into a wall socket. Turn on the switch on the
wall socket (if available).
Press
Power to switch on the projector.
If this is the first time that you've switched on the projector, please refer to on-screen
instructions and select your OSD language and Projection mode.
Switch on all connected equipment.
The projector will then begin a search of the input signals. The options indicating green
light dots are the signal sources currently available. If the projector fails to detect a valid
signal, the screen will display a
[NO SIGNAL]
message until an input signal is found.
You can also press the [Source] key or the shortcut key on the remote control to select the
desired input signals. Please refer to
“Switching input signal”
for the details.
If the input signal frequency / resolution is outside the operating range of the projector, the
blank screen will display the [Out of Range] message. Please change to an input signal which is
compatible with the projector's resolution or set the input signal to a lower setting. For more
details, please refer to the
“Timing chart”
.