ViewSonic LS820 LS810 User Guide English - Page 44

Using the CEC function, 3D functions, Using the projector under standby mode

Get ViewSonic LS820 PDF manuals and user guides View all ViewSonic LS820 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Using the CEC function This projector supports Consumer Electronics Control (CEC), allowing you to connect to connect to HDMI and achieve synchronized power ON/OFF operations. This means that when a device that also supports CEC is connected to the HDMI input jack of the projector, switching off the power of the projector will also automatically switch off the power of the connected device. Switching on the power of the connected device will also automatically switch on the projector. Activating the CEC function: 1. Open the OSD menu and enter Power management > Auto Power On > CEC menu. 2. Press / and select Enable. To ensure proper operations of the CEC function, please verify that the target device has been connected to the HDMI input jack via an HDMI cable and that the CEC function has been activated. CEC function may not be usable according to the connected equipment. 3D functions This projector also comes with 3D functions that offer greater depth and immersion when viewing 3D movies, videos, sports, and games. You would need a pair of 3D glasses when viewing 3D images and videos. If the 3D signal comes from an HDMI 1.4a compatible device, this projector will look for a 3D Sync data signal. Once detected, the projector will automatically switch to 3D projection. Under other circumstances, you may need to manually select the 3D Sync format to ensure that the proper projection of 3D images. Selecting 3D Sync formats: 1. Use the 3D button on the remote control to enter the 3D Settings menu or enter Advanced > 3D Settings menu. 2. Press [Enter] to bring up the 3D Settings page. 3. Highlight 3D Glasses and press / to select DLP or 3D VESA. Once 3D Sync function has been activated: • Brightness of the projected image will be reduced. • Color modes cannot be adjusted. • Zoom functions can only enlarge the image to a limited degree. If the 3D image has been severely inverted, you may set the 3D Sync Invert function to [Invert] to correct this problem. Using the projector under standby mode A number of projector functions can be used under Standby Mode (plugged in to power but not switched on). To use these functions, please check that you have switched on the Power management > Standby Settings and its secondary menu items, and that the cables have been properly connected. Refer to the chapter on cable connections for more information on cable connections. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
37
Using the CEC function
This projector supports Consumer Electronics Control (CEC), allowing you to connect
to connect to HDMI and achieve synchronized power ON/OFF operations. This
means that when a device that also supports CEC is connected to the HDMI input
jack of the projector, switching off the power of the projector will also automatically
switch off the power of the connected device. Switching on the power of the
connected device will also automatically switch on the projector.
Activating the CEC function:
1.
Open the OSD menu and enter
Power management
>
Auto Power On
>
CEC
menu.
2.
Press
/
and select
Enable
.
To ensure proper operations of the CEC function, please verify that the target device has been
connected to the HDMI input jack via an HDMI cable and that the CEC function has been
activated.
CEC function may not be usable according to the connected equipment.
3D functions
This projector also comes with 3D functions that offer greater depth and immersion
when viewing 3D movies, videos, sports, and games. You would need a pair of 3D
glasses when viewing 3D images and videos.
If the 3D signal comes from an HDMI 1.4a compatible device, this projector will look
for a 3D Sync data signal. Once detected, the projector will automatically switch to 3D
projection. Under other circumstances, you may need to manually select the 3D Sync
format to ensure that the proper projection of 3D images.
Selecting 3D Sync formats:
1.
Use the 3D button on the remote control to enter the
3D Settings
menu or enter
Advanced
>
3D Settings
menu.
2.
Press [Enter] to bring up the
3D Settings
page.
3.
Highlight
3D Glasses
and press
/
to select
DLP
or
3D VESA
.
Once 3D Sync function has been activated:
• Brightness of the projected image will be reduced.
• Color modes cannot be adjusted.
• Zoom functions can only enlarge the image to a limited degree.
If the 3D image has been severely inverted, you may set the 3D Sync Invert function to [Invert]
to correct this problem.
Using the projector under standby mode
A number of projector functions can be used under Standby Mode (plugged in to
power but not switched on). To use these functions, please check that you have
switched on the
Power management > Standby Settings
and its secondary menu
items, and that the cables have been properly connected. Refer to the chapter on
cable connections for more information on cable connections.