Home » ViewSonic Manuals » Projectors » ViewSonic PJD6230 » Manual Viewer

ViewSonic PJD6230 User Guide - Page 44

ViewMatch, Aspect Ratio, ECO On, ECO Off, Auto Source On, Auto Source Off, Factory Reset, Lamp Hour

UPC - 766907322828

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

ViewMatch Command Send String BE,EF,03,06,00,38,5A,88,00,00,00,00,00 Response 6 Comment Aspect Ratio Command Send String BE, EF, 03, 06, 00, 0D, DA, 68, 00, 00, 00, 00, 00 Response 06 Comment ECO On Command Send String BE, EF, 03, 06, 00, EF, DB, 6A, 00, 00, 00, 00, 00 Response 06 Comment ECO Off Command Send String BE, EF, 03, 06, 00, 3E, DA, 6B, 00, 00, 00, 00, 00 Response 06 Comment Auto Source On Command Send String BE, EF, 03, 06, 00, 89, DB, 6C, 00, 00, 00, 00, 00 Response 06 Comment Auto Source Off Command Send String BE, EF, 03, 06, 00, 58, DA, 6D, 00, 00, 00, 00, 00 Response 06 Comment Factory Reset Command Send String BE, EF, 03, 06, 00, 6B, DA, 6E, 00, 00, 00, 00, 00 Response 06 Comment Lamp Hour Command Send String BE, EF, 03, 06, 00, BA, DB, 6F, 00, 00, 00, 00, 00 Response Lamp Hour Comment ViewSonic 37 PJD6220/PJD6230/PJD6240

Section	Page
PJD6220_Contents_Eng.pdf	8
Projector Features	8
Package Contents	9
Projector with Lens Cap	9
AC Power Cord	9
VGA Cable (D-SUB to D-SUB)	9
Quick Start Guide	9
VGA - Component Adapter	9
Projector Overview	10
Using the Product	12
Control Panel	12
Connection Ports	13
Remote Control	14
Installing the Batteries	15
1. Open the battery cover in the direction shown.	15
2. Install batteries as indicated by the diagram Inside the compartment.	15
3. Close the battery cover into position.	15
Remote Control Operation	16
Installation	17
Connecting the Projector	17
Powering On/Off the Projector	18
Powering On the Projector:	18
1. Remove the projector lens cap.	18
2. Complete the AC power cord and peripheral signal cable(s) connections.	18
3. Press button to turn on the projector. The projector takes a minute or so to warm up.	18
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.	18
Powering Off the Projector:	18
1. Press button to turn off the projector lamp. You will see a message \	18
2. Press button again to confirm.	18
3. Disconnect the AC power cord from the electrical outlet and the projector.	18
4. Do not turn on the projector immediately following a power off procedure.	18
Adjusting the Projector	19
Adjusting the Projector Height	19
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.	19
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.	19
Adjusting the Projector Zoom and Focus	19
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.	19
2. Adjust the image by sliding the zoom ring.	19
Adjusting Projection Image Size	20
Menu Operation	21
1. Press the Menu button on the control panel or the MENU button on the remote control to open the OSD menu.	22
2. When OSD is displayed, use p / q to select any feature in the main menu.	22
3. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.	22
4. Adjust the settings with t / u.	22
5. Press the Menu buttonon the control panel or the MENU button on the remote control, the screen will return to the main menu.	22
6. To exit OSD, press the Menu button on the control panel or the MENU button on the remote control again. The OSD menu will close and the projector will automatically save the new settings.	22
Maintenance	37
Cleaning the Lens	37
Cleaning the Projector Housing	37
Replacing the Lamp	38
1. Turn off the projector.	39
2. If the projector is installed in a ceiling mount, remove it from the mount.	39
3. Unplug the power cord.	39
4. Loosen the screw in the side of the lamp cover and remove the cover.	39
5. Remove the screws from the lamp module, raise the handle, and lift out the module.	39
6. Insert the new lamp module into the projector and tighten the screws.	39
7. Replace the lamp cover and tighten the screw.	39
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.	39
9. Reset the lamp hour. Refer to the “Setting” menu.	39
Specifications	40
Appendix	41
LED Indicator Messages	41
Compatibility Modes	47
Computer:	47
Video:	47
Troubleshooting	48
Start-up problems	48