Viking DDSF136DSS Installation Instructions - Page 14

Prepare the Water System - filter

Get Viking DDSF136DSS PDF manuals and user guides View all Viking DDSF136DSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Installation Instructions Prepare the Water System Please read before using the water system. Immediately after installation, follow the steps below to make sure that the water system is properly cleaned. 1. Open the freezer door and turn off the ice maker. The On/Off switch is located on the top right side of the freezer compartment. Move the switch to the OFF (right) setting as shown. NOTE: Make sure the base grille filter is properly installed and the cap is in the horizontal position. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. 2. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser. 3. Open the freezer door and turn on the ice maker. Move the switch to the ON (left) position. See the Use & Care Guide for further instructions on the operation of your ice maker. • Allow 24 hours to produce the first batch of ice. • Discard the first three batches of ice produced. • Depending on your model, you may want to select the maximum ice feature to increase the production of ice. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
12
Installation Instructions
Prepare the Water System
Please read before using the water system.
Immediately after installation, follow the steps below to make sure that the water system is properly
cleaned.
1. Open the freezer door and turn off the ice maker. The On/Off switch is located on the top right side
of the freezer compartment. Move the switch to the OFF (right) setting as shown.
NOTE:
Make sure the base grille filter is properly installed and the cap is in the horizontal position.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfec-
tion before or after the system. Systems certified for cyst reduction may be used on disinfected waters
that may contain filterable cysts.
2. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it
for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and
releasing the dispenser lever (5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has been dis
-
pensed. This will flush air from the filter and water dispensing system, and prepare the water filter for
use. Additional flushing may be required in some households. As air is cleared from the system, water
may spurt out of the dispenser.
3. Open the freezer door and turn on the ice maker. Move the switch to the ON (left) position. See the
Use & Care Guide for further instructions on the operation of your ice maker.
Allow 24 hours to produce the first batch of ice.
•
Discard the first three batches of ice produced.
•
Depending on your model, you may want to select the maximum ice feature to increase the pro
-
•
duction of ice.