Vizio P50HDTV10A User Manual - Page 30

Setting Up to Watch Television

Get Vizio P50HDTV10A PDF manuals and user guides View all Vizio P50HDTV10A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

VIZIO P50HDTV User Manual Chapter 3 Setting Up to Watch Television For 'Preparing Your Plasma TV for Wall Mounting', see page 6. 3.1 Basic Plasma TV Start Up 1. Connecting the Power Cable Connect the power cord to the power cord connector on the back of the Plasma TV, and then plug the power cord into an AC wall socket. 2. Connect Audio and Video Cables to the Plasma TV (see pages 16 ~ 29 for detailed steps) 3. Turning Power On Once all the components are connected, press the Power ON button on the side of the Plasma TV, or press the Power ON (Red) button on the remote control. 4. Select Input Source Select the Input Source for the Plasma TV by pressing the INPUT button on the side of the TV or using the Input button on the remote control. Pressing this button will cycle through the following options: DTV, TV, RGB, AV1 (S-Video or Video*), AV2 (S-Video or Video*), Component 1, Component 2, HDMI 1 and HDMI 2. *S-Video has priority. If a signal is connected to AV1 S-Video by itself or signals are connected to AV1 S-Video and AV1 Video simultaneously, then S-Video will be the only choice for AV1. If a signal is connected to AV1 Video only, then Video will be the only choice for AV1. The same input priority scheme applies to AV2. 5. Using TV with an Antenna or Cable When an antenna or cable source is connected to the DTV/TV input, you will need to select TV using the INPUT button on the remote or side of the Plasma TV, or directly by pressing the TV button on the Remote Control, and Auto Scan for the available TV channels. Please follow the instructions below: a. Select TV input (see Step 4 above) by pressing the INPUT button on the side of the Plasma TV or using the INPUT button on the remote control, or directly by pressing the TV button on the remote control. The screen will show 'snow' and an information panel that says, "Channel Scan Required Press Menu." Note: If you do not see this option within the OSD, you might have selected the wrong input in the previous steps and you will need to repeat step 4 (above) to select the correct input source. Version 5/23/2006 30 www.VIZIOCE.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
VIZIO P50HDTV User Manual
Version 5/23/2006
30
www.VIZIOCE.com
Chapter 3
Setting Up to Watch Television
For ‘Preparing Your Plasma TV for Wall Mounting’, see page 6.
3.1
Basic Plasma TV Start Up
1.
Connecting the Power Cable
Connect the power cord to the power cord connector on the back of the Plasma TV, and then
plug the power cord into an AC wall socket.
2.
Connect Audio and Video Cables to the Plasma TV
(see pages 16 ~ 29 for detailed steps)
3.
Turning Power On
Once all the components are connected, press the Power ON button on the side of the Plasma
TV, or press the Power ON (Red) button on the remote control.
4.
Select Input Source
Select the Input Source for the Plasma TV by pressing the INPUT button on the side of the TV or
using the Input button on the remote control.
Pressing this button will cycle through the following
options: DTV, TV, RGB, AV1 (S-Video or Video*), AV2 (S-Video or Video*), Component 1,
Component 2, HDMI 1 and HDMI 2.
5.
Using TV with an Antenna or Cable
When an antenna or cable source is connected to
the DTV/TV input, you will need to select TV using
the INPUT button on the remote or side of the
Plasma TV, or directly by pressing the TV button on
the Remote Control, and Auto Scan for the available
TV channels.
Please follow the instructions below:
a.
Select TV input (see Step 4 above) by pressing the INPUT button on the side of the
Plasma TV or using the INPUT button on the remote control, or directly by pressing the
TV button on the remote control.
The screen will show ‘snow’ and an information panel
that says, “Channel Scan Required
Press Menu.”
Note: If you do not see this option within the OSD, you might have selected the wrong input in the
previous steps and you will need to repeat step 4 (above) to select the correct input source.
*S-Video has priority.
If a signal is connected to AV1 S-Video by itself or signals are connected to AV1
S-Video and AV1 Video simultaneously, then S-Video will be the only choice for AV1.
If a signal is
connected to AV1 Video only, then Video will be the only choice for AV1.
The same input priority
scheme applies to AV2.