Weider Pro 9648 English Manual - Page 14

Locate the Low Cable 23.

Get Weider Pro 9648 PDF manuals and user guides View all Weider Pro 9648 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

CABLE ASSEMBLY 25. Locate the Low Cable (23). Route the Low 25 Cable under the 3 1/2Ó Low Pulley (76) attached to the lower hole in the Press Frame (17). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame and that the Cable is between the Pulley and the crossbar on the Press Frame. Tighten the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 3 3/4Ó Bolt (not shown). Crossbar 21 76 23 Ball 17 26. Route the Low Cable (23) around the 3 1/2Ó Pulley (15) attached to the lower hole in the Front Upright (42). See the inset drawing. Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 3 3/4Ó Bolt (88). 26 21 42 15 23 15 88 66 42 Inset shows view from other side 23 27. Route the Low Cable (23) around the 3 1/2Ó Pulley (15) attached to the upper hole in the 27 Press Frame (17). Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 3 1/2Ó Bolt (not shown). 23 15 21 66 17 28. Route the Low Cable (23) around the 3 1/2Ó Pulley (15) attached to the upper hole in the 28 Front Upright (42). See the inset drawing. 23 Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the 15 42 Cable is routed around the Pulley as shown. Tighten the 3/8Ó Nylon Locknut (21) 21 and the 3/8Ó x 3 3/4Ó Bolt (88). 23 15 88 66 42 Inset shows view from other side 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
14
25.
Locate the Low Cable (23).
Route the Low
Cable under the 3 1/2° Low Pulley (76)
attached to the lower hole in the Press Frame
(17).
Be sure that the end of the Cable with
the ball is on the indicated side of the
Press Frame and that the Cable is between
the Pulley and the crossbar on the Press
Frame.
Tighten the 3/8° Nylon Locknut (21)
and the 3/8° x 3 3/4° Bolt (not shown).
26.
Route the Low Cable (23) around the 3 1/2°
Pulley (15) attached to the lower hole in the
Front Upright (42).
See the inset drawing.
Be sure that the Cable Trap (66) is turned
to hold the Cable in place and that the
Cable is routed around the Pulley as
shown.
Tighten the 3/8° Nylon Locknut (21)
and the 3/8° x 3 3/4° Bolt (88).
27.
Route the Low Cable (23) around the 3 1/2°
Pulley (15) attached to the upper hole in the
Press Frame (17).
Be sure that the Cable
Trap (66) is turned to hold the Cable in
place and that the Cable is routed around
the Pulley as shown.
Tighten the 3/8° Nylon
Locknut (21) and the 3/8° x 3 1/2° Bolt (not
shown).
28.
Route the Low Cable (23) around the 3 1/2°
Pulley (15) attached to the upper hole in the
Front Upright (42).
See the inset drawing.
Be sure that the Cable Trap (66) is turned
to hold the Cable in place and that the
Cable is routed around the Pulley as
shown.
Tighten the 3/8° Nylon Locknut (21)
and the 3/8° x 3 3/4° Bolt (88).
28
25
23
26
Inset shows view
from other side
27
CABLE ASSEMBLY
21
17
Ball
42
88
23
23
21
15
15
42
66
Inset shows view
from other side
42
88
23
23
15
15
66
42
21
23
17
66
15
76
Crossbar
21