Weider Pro 9648 English Manual - Page 17

Insert the Bolt through the Pivot Arm 101

Get Weider Pro 9648 PDF manuals and user guides View all Weider Pro 9648 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

34. See inset drawing A. Attach a 3 1/2Ó Pulley 34 (15) and a Cable Trap (66) to the upper hole in the Long ÒUÓ-Bracket (57) with a 3/8Ó x 2Ó Bolt (12) and a 3/8Ó Nylon Locknut (21). Be sure that the Cable Trap is inside the Long ÒUÓ-Bracket. (Note: This may come pre- assembled.) Route the Military Press Cable (72) through the Long ÒUÓ-Bracket (57) and the 3 1/2Ó Pulley (15). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. See inset drawing B. Slide a 5/16Ó Flat Washer (8) onto a 5/16Ó x 2 3/4 Bolt (11). Insert the Bolt through the Pivot Arm (101) from the indicated side. Tighten a 5/16Ó Nylon Jam Nut (93) onto the Bolt. Slide the end of the Military Press Cable (72) onto the end of the Bolt. Thread another 5/16Ó Nylon Jam Nut onto the Bolt. Do not fully tighten the second Jam Nut. There must be room between the two Jam Nuts for the end of the Cable to pivot. 15 57 72 21 57 11 8 15 A 66 12 B 101 93 72 CABLE ASSEMBLY 35. Locate the Leg Press Cable (99). Attach the 35 end of the Leg Press Cable to the Long ÒUÓ- Bracket (57) with a 1/4Ó Nylon Locknut (2) and a 1/4Ó Flat Washer (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing. Wrap the Leg Press Cable (99) around a 3 1/2Ó Pulley (15). Attach the Pulley to the Leg Press Upright (56) with the 3/8Ó x 3 1/2Ó Bolt (16), a 3/8Ó Flat Washer (9), and a 3/8Ó Nylon Locknut (21). The ball on the Cable must be on the indicated side of the Pulley. Be sure that the Cable and Pulley move smoothly and that the Cable is between the Pulley and the welded rod. 2 10 57 16 15 99 17 99 Welded 2 Rod 10 57 56 Ball 9 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
17
34.
See inset drawing A. Attach a 3 1/2° Pulley
(15) and a Cable Trap (66) to the upper hole
in the Long ²U°-Bracket (57) with a 3/8° x 2°
Bolt (12) and a 3/8° Nylon Locknut (21).
Be
sure that the Cable Trap is inside the Long
±U²-Bracket. (Note: This may come pre-
assembled.
)
Route the Military Press Cable (72) through
the Long ²U°-Bracket (57) and the 3 1/2°
Pulley (15).
Be sure that the Cable is in the
groove of the Pulley and that the Cable
and Pulley move smoothly.
See inset drawing B. Slide a 5/16° Flat
Washer (8) onto a 5/16° x 2 3/4 Bolt (11).
Insert the Bolt through the Pivot Arm (101)
from the indicated side. Tighten a 5/16° Nylon
Jam Nut (93) onto the Bolt. Slide the end of
the Military Press Cable (72) onto the end of
the Bolt. Thread another 5/16° Nylon Jam Nut
onto the Bolt.
Do not fully tighten the sec-
ond Jam Nut. There must be room
between the two Jam Nuts for the end of
the Cable to pivot.
35.
Locate the Leg Press Cable (99).
Attach the
end of the Leg Press Cable to the Long ²U°-
Bracket (57) with a 1/4° Nylon Locknut (2) and
a 1/4° Flat Washer (10).
Do not completely
tighten the Nylon Locknut. It should be
threaded onto the end of the Cable only a
couple of turns, as shown in the inset
drawing.
Wrap the Leg Press Cable (99) around a
3 1/2° Pulley (15). Attach the Pulley to the Leg
Press Upright (56) with the 3/8° x 3 1/2° Bolt
(16), a 3/8° Flat Washer (9), and a 3/8° Nylon
Locknut (21).
The ball on the Cable must be
on the indicated side of the Pulley. Be sure
that the Cable and Pulley move smoothly
and that the Cable is between the Pulley
and the welded rod.
34
35
CABLE ASSEMBLY
56
Ball
9
21
15
2
10
16
72
15
21
57
A
B
12
101
8
15
66
57
93
2
10
57
57
99
99
Welded
Rod
72
11