Weider Total Body Works 5000 Bench Uk Manual - Page 6

the Bolt and an M10 Nylon Locknut 45.

Get Weider Total Body Works 5000 Bench PDF manuals and user guides View all Weider Total Body Works 5000 Bench manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

2. Make sure that the Bungee Cords (35) are resting 2 in the brackets on the Backrest Frame (3). Attach the Backrest (4) to the Backrest Frame with four M6 x 38mm Screws (51) and four M6 Washers (39). Make sure that the Backrest is holding the 4 Bungee Cords in place. 35 39 3 51 39 3. Grease an M10 x 80mm Bolt (43). Attach the 3 Support Leg (7) to the Adjustment Bracket (48) with the Bolt and an M10 Nylon Locknut (45). Do not overtighten the Locknut; the Support Leg must be able to pivot easily. Slide the Adjustment Bracket (48) onto the Adjustment Leg (5). Engage the indicated Knob (58) into the Adjustment Leg, and fully tighten the Knob. 4. Note: The backrest is not shown in this step for clarity. 4 Grease an M10 x 175mm Bolt (42). Attach the Adjustment Leg (5) to the Top Frame (1) with the Bolt and an M10 Nylon Locknut (45). Do not overtighten the Bolt; the Adjustment Leg must be able to pivot easily. Grease two M10 x 20mm Screws (9). Attach the Support Leg (7) to the Top Frame (1) with the Screws. Do not overtighten the Screws; the Support Leg must be able to pivot easily. 51 7 45 5 48 Grease 58 43 9 Grease 45 9 1 42 Grease Grease 7 5 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
6
Grease
9
9
5
45
4
7
42
Grease
Grease
1
4.
Note: The backrest is not shown in this step for
clarity.
Grease an M10 x 175mm Bolt (42). Attach the
Adjustment Leg (5) to the Top Frame (1) with the
Bolt and an M10 Nylon Locknut (45).
Do not over-
tighten the Bolt; the Adjustment Leg must be
able to pivot easily.
Grease two M10 x 20mm Screws (9). Attach the
Support Leg (7) to the Top Frame (1) with the
Screws.
Do not overtighten the Screws; the
Support Leg must be able to pivot easily.
2
4
3
39
51
39
51
35
2.
Make sure that the Bungee Cords (35) are resting
in the brackets on the Backrest Frame (3). Attach
the Backrest (4) to the Backrest Frame with four M6
x 38mm Screws (51) and four M6 Washers (39).
Make sure that the Backrest is holding the
Bungee Cords in place.
Grease
7
5
3
48
58
45
43
3.
Grease an M10 x 80mm Bolt (43). Attach the
Support Leg (7) to the Adjustment Bracket (48) with
the Bolt and an M10 Nylon Locknut (45).
Do not
overtighten the Locknut; the Support Leg must
be able to pivot easily.
Slide the Adjustment Bracket (48) onto the
Adjustment Leg (5). Engage the indicated Knob
(58) into the Adjustment Leg, and fully tighten the
Knob.