Weslo Eclipse 2 Elliptical User Manual - Page 11

Maintenance

Get Weslo Eclipse 2 Elliptical PDF manuals and user guides View all Weslo Eclipse 2 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

MAINTENANCE CONSOLE TROUBLE-SHOOTING If the console does not function properly, the batteries should be replaced. To replace the batteries, see assembly step 6 on page 6. In addition, make sure that the console wire is connected to the extension wire. See assembly step 6 on page 6. HOW TO ADJUST THE REED SWITCH If the console does not display correct feedback, the reed switch should be adjusted. To adjust the reed switch, the Side Shield (27) must first be removed. Remove the Crank Cover (62) and the 5/16" x 3/4" Tap Screw (18) from the left Crank Arm (10). Slide the left Crank Arm off the Crank Shaft (11). Remove the right Crank Arm (not shown) in the same way. Next, locate the Reed Switch (48). Turn the Pulley (19) until the Magnet (55) is aligned with the Reed Switch. 55 51 Loosen, but do 48 not remove, the M4 x 12mm 19 Screw (51). Slide the Reed Switch slightly toward or away from the Magnet. Make sure that the Magnet will not hit the Reed Switch. Retighten the Screw. Turn the Pulley (19) for a moment. Repeat until the console displays correct feedback. When the Reed Switch is correctly adjusted, reattach the Side Shield and the Crank Arms. Top 10 27 Back 18 11 62 4 Remove the three M4 x 38mm Screws (4) from each side of the Side Shield (27). Hold the Side Shield (27) near the back and pull it apart slightly until the Side Shield can be lifted off the ends of the Crank Shaft (11). Remove the Side Shield. Do not pull the Side Shield apart at the top or the seam may be broken. HOW TO ADJUST THE RESISTANCE STRAP If the pedals do not have enough resistance, even when the resistance knob is turned to the maximum setting, the Resistance Strap (31) may need to be adjusted. To adjust the Resistance Strap, the side shield must first be removed. Refer to the instructions at the left to remove the side shield. Turn the resistance knob to the lowest setting. (See HOW TO ADJUST THE RESISTANCE OF THE PEDALS on page 5.) Grip the end of the Resistance Strap (31) and pull it away from the rest of the Strap. Next, pull the end of the 19 Strap up to remove any 31 slack. Then press the end of the Strap against the rest of the Strap as shown. Turn the Pulley (19) for a moment to make sure that there is not too much resistance. When the Resistance Strap is properly adjusted, reattach the Side Shield and the Crank Arms. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
11
MAINTENANCE
CONSOLE TROUBLE-SHOOTING
If the console does not function properly, the batteries
should be replaced. To replace the batteries, see
assembly step 6 on page 6. In addition, make sure
that the console wire is connected to the extension
wire. See assembly step 6 on page 6.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, the Side Shield (27) must first be removed.
Remove the Crank Cover (62) and the 5/16” x 3/4”
Tap Screw (18) from the left Crank Arm (10). Slide the
left Crank Arm off the Crank Shaft (11). Remove the
right Crank Arm (not shown) in the same way.
Remove the three M4 x 38mm Screws (4) from each
side of the Side Shield (27).
Hold the Side Shield (27) near the back and pull it
apart slightly until the Side Shield can be lifted off the
ends of the Crank Shaft (11). Remove the Side Shield.
Do not pull the Side Shield apart at the top or the
seam may be broken.
Next, locate the
Reed Switch (48).
Turn the Pulley
(19) until the
Magnet (55) is
aligned with the
Reed Switch.
Loosen, but do
not remove, the
M4 x 12mm
Screw (51). Slide
the Reed Switch
slightly toward or away from the Magnet. Make sure
that the Magnet will not hit the Reed Switch. Retighten
the Screw. Turn the Pulley (19) for a moment. Repeat
until the console displays correct feedback. When the
Reed Switch is correctly adjusted, reattach the Side
Shield and the Crank Arms.
HOW TO ADJUST THE RESISTANCE STRAP
If the pedals do not have enough resistance, even
when the resistance knob is turned to the maximum
setting, the Resistance Strap (31) may need to be
adjusted. To adjust the Resistance Strap, the side
shield must first be removed. Refer to the instructions
at the left to remove the side shield.
Turn the resistance knob to the lowest setting. (See
HOW TO ADJUST THE RESISTANCE OF THE
PEDALS on page 5.) Grip the end of the Resistance
Strap (31) and
pull it away from
the rest of the
Strap. Next, pull
the end of the
Strap up to
remove any
slack. Then press
the end of the
Strap against the
rest of the Strap
as shown. Turn
the Pulley (19) for
a moment to make sure that there is not too much
resistance. When the Resistance Strap is properly
adjusted, reattach the Side Shield and the Crank
Arms.
48
19
31
55
51
19
27
10
11
18
62
Back
Top
4