Whirlpool GCEM2990TQ Installation Instructions - Page 11

Installation, Instructions- Electricdryer

Get Whirlpool GCEM2990TQ PDF manuals and user guides View all Whirlpool GCEM2990TQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

iNSTALLATIONiNSTRUCTIONS- ELECTRICDRYER NOTE: Slide dryer onto cardboard or hardboard before moving to avoid damaging floor covering. f, Using two or more people, move dryer to desired installation location. 2, Take tape off front corners of dryer. Open dryer and remove the literature and parts packages. Wipe the intedor of the drum thoroughly with a damp cloth. 3, Take two of the cardboard corners from the carton and place them on the floor in back of the dryer. Firmly grasp the body of the dryer and gently lay it on its back on the cardboard corners. 4, With one of the legs in hand, check the ridges for a diamond marking. That's how far the leg is supposed to go into the hole. 5, Start to screw the leveling legs into the holes by hand. (Use a small amount of liquid detergent to lubricate the screw threads so it is easier to turn the legs.) Use a 1-inch wrench or socket wrench to finish turning the legs until you reach the diamond mark. Now stand the dryer up. 6, Remove cardboard or hardboard from under dryer. Power Supply Cord Method This dryer is manufactured with the neutral ground wire connected to the neutral (center) of the wiring harness at the terminal b!ock. If local codes do not permit this type of connection, use "Four-wire connection" instructions. Use a UL-Iisted power supply cord rated 240-volt min., 30-amp and marked for use with a clothes dryer. Fire Hazard Use a new UL listed 30 amp power supply cord, Use a UL listed strain relief. Disconnect power before making electrica_ connections. Connect neutral wire (white or center wire) to center termina_ (sHyer). Ground wire (green or bare wire) must be connected to green ground connector. Connect remaining 2 supply wires to remaining 2 terminals (gold). Securely tighten aH e_ectrica_ connections. Failure to do so can recur in death, fire, or e_ectrica_ shock. f° Disconnect power. 2, Remove hold-down screw and the terminal block cover. A. External ground conductor screw B, Tab C, Terrninalblock cover D. Hold-down screw 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
iNSTALLATION
iNSTRUCTIONS- ELECTRICDRYER
NOTE: Slide dryer onto cardboard
or hardboard
before moving to
avoid damaging
floor covering.
f,
Using two or more people, move dryer to desired installation
location.
2,
Take tape off front corners
of dryer. Open dryer and remove
the literature
and parts packages.
Wipe the intedor of the
drum thoroughly
with a damp cloth.
3,
Take two of the cardboard
corners
from the carton and place
them on the floor in back of the dryer. Firmly grasp the body
of the dryer and gently lay it on its back on the cardboard
corners.
4,
With one of the legs in hand, check the ridges for a diamond
marking.
That's how far the leg is supposed
to go into the
hole.
5,
Start to screw the leveling
legs into the holes by hand. (Use a
small amount of liquid detergent
to lubricate the screw
threads so it is easier to turn the legs.) Use a 1-inch wrench or
socket
wrench to finish turning the legs until you reach the
diamond
mark.
Now stand the dryer up.
6,
Remove cardboard
or hardboard
from under dryer.
Power
Supply
Cord
Method
This dryer is manufactured
with the neutral ground wire
connected
to the neutral (center) of the wiring harness at the
terminal b!ock. If local codes do not permit
this type of
connection,
use "Four-wire connection"
instructions.
Use a UL-Iisted
power supply
cord rated 240-volt
min., 30-amp
and marked for use with
a clothes dryer.
Fire Hazard
Use a new UL listed
30 amp power
supply
cord,
Use a UL
listed
strain
relief.
Disconnect
power
before
making
electrica_
connections.
Connect
neutral
wire
(white
or center
wire) to center
termina_
(sHyer).
Ground
wire
(green
or bare wire)
must
be connected
to
green
ground
connector.
Connect
remaining
2 supply
wires
to remaining
2 terminals
(gold).
Securely
tighten
aH e_ectrica_ connections.
Failure
to do so can
recur
in death, fire, or
e_ectrica_ shock.
f°
Disconnect
power.
2,
Remove hold-down
screw and the terminal block cover.
A. External ground
conductor screw
B, Tab
C, Terrninalblock cover
D. Hold-down
screw
11