Whirlpool WDT705PAK Owners Manual - Page 21

Option C: Waste disposer - with air gap, Option D: No waste disposer - with air gap

Get Whirlpool WDT705PAK PDF manuals and user guides View all Whirlpool WDT705PAK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Option C: Waste disposer - with air gap Option D: No waste disposer - with air gap Helpful Tip: Remove disposer knockout plug. 1. Using a hammer and screwdriver, knock plug into disposer. 2. Use needle-nose pliers to remove plug. 3. Connect rubber end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. 4. Attach drain hose to air gap with large drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1 1/2" to 2" (38 mm to 50 mm) screwtype clamp (not provided). 5. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from air gap to disposer inlet. 1. Connect rubber end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. 2. Attach drain hose to air gap with large drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1 1/2" to 2" (38 mm to 50 mm) screwtype clamp (not provided). 3. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from waste tee to air gap. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
21
Option C: Waste disposer – with air gap
Helpful Tip:
Remove disposer knockout plug.
1.
Using a hammer and screwdriver,
knock plug into disposer.
2.
Use needle-nose pliers to remove plug.
3.
Connect rubber end of drain hose to air
gap and cut if needed.
NOTE:
Do not cut ribbed section.
4.
Attach drain hose to air gap with large
drain hose clamp (provided). Use pliers
to squeeze clamp open and move into
position. If the drain hose was cut, use
a 1 1/2” to 2" (38 mm to 50 mm) screw-
type clamp (not provided).
5.
Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from air gap to disposer inlet.
Option D: No waste disposer – with air gap
1.
Connect rubber end of drain hose to air
gap and cut if needed.
NOTE:
Do not cut ribbed section.
2.
Attach drain hose to air gap with large
drain hose clamp (provided). Use pliers
to squeeze clamp open and move into
position. If the drain hose was cut, use
a 1 1/2" to 2" (38 mm to 50 mm) screw-
type clamp (not provided).
3.
Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from waste tee to air gap.