Xerox 7300DN Network Users Guide - Page 7

Setting the IP address from the front panel, Printer Installer and Utilities CD-ROM

Get Xerox 7300DN - Phaser Color Laser Printer PDF manuals and user guides View all Xerox 7300DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

IP Address  PostScript Utility files can be used on hosts that do not have BOOTP or DHCP- see the ReadMe file on the Printer Installer and Utilities CD-ROM. The PC ReadMe file is in the UTILS directory of the Printer Installer and Utilities CD-ROM; the Macintosh ReadMe file is in the Network Utilities folder. Note When two or more IP address methods are used simultaneously, the printer uses the first address that it successfully obtains. Information Required for IP Addressing Information Internet (IP) address for the printer Network Mask Default Router/Gateway address Comments Format is xxx.xxx.xxx.xxx, where xxx represents a decimal number from 0 - 255. If you are unsure, leave this blank; the printer chooses an appropriate mask. If you want to communicate with the printer from anywhere other than the local network segment, you need the router address. Setting the IP address from the front panel For information about using the front panel, refer to the Front Panel section of the Features Guide on the Interactive Documentation CD-ROM. Note DHCP must be set to OFF before you can set the IP address from the printer's front panel. 1. With Menus highlighted, press the OK key. 2. Press the Down Arrow key to scroll to the Connection Setup Menu and press the OK key. 3. Scroll to TCP/IP Address Menu by pressing the Down Arrow key and press the OK key. 4. Scroll to TCP/IP Address by pressing the Up Arrow or Down Arrow key. Press the OK key. 5. Verify the number of characters in the IP address. There should be 12 characters. IP addresses are entered in xxx.xxx.xxx.xxx format, where each segment represents a number from 0-255. 6. By pressing the Up Arrow or Down Arrow key, scroll to the correct number for the first segment of the address. Press the OK key to accept that segment. 7. Repeat Step 6 for each remaining segment. 8. Scroll to TCP/IP Network Mask by pressing the Up Arrow or Down Arrow key. 9. By pressing the Up Arrow or Down Arrow key, scroll to the correct number for the first segment of the address. Press the OK key to accept that segment. 10. Repeat Step 9 for each remaining segment. 11. Scroll to TCP/IP Gateway by pressing the Up Arrow or Down Arrow key. 12. Scroll to the correct number for the first segment of the address by pressing the Up Arrow or Down Arrow key. Press the OK key to accept that segment. 13. Repeat Step 12 for each remaining segment. 14. To exit the menu system, scroll to Exit and press the OK key. Phaser® 7300 Color Printer 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
IP Address
Phaser® 7300 Color Printer
2
PostScript Utility files can be used on hosts that do not have BOOTP or DHCP— see the ReadMe
file on the
Printer Installer and Utilities CD-ROM
. The PC ReadMe file is in the
UTILS
directory of the
Printer Installer and Utilities CD-ROM
; the Macintosh ReadMe file is in the
Network Utilities
folder.
Note
When two or more IP address methods are used simultaneously, the printer uses the first
address that it successfully obtains.
Setting the IP address from the front panel
For information about using the front panel, refer to the
Front Panel
section of the
Features Guide
on
the
Interactive Documentation CD-ROM
.
Note
DHCP must be set to
OFF
before you can set the IP address from the printer’s front panel.
1.
With
Menus
highlighted, press the
OK
key.
2.
Press the
Down Arrow
key to scroll to the
Connection Setup Menu
and press the
OK
key.
3.
Scroll to
TCP/IP Address Menu
by pressing the
Down Arrow
key and press the
OK
key.
4.
Scroll to
TCP/IP Address
by pressing the
Up Arrow
or
Down Arrow
key. Press the
OK
key.
5.
Verify the number of characters in the IP address. There should be 12 characters. IP addresses are
entered in
xxx.xxx.xxx.xxx
format, where each segment represents a number from 0-255.
6.
By pressing the
Up Arrow
or
Down Arrow
key, scroll to the correct number for the first segment
of the address. Press the
OK
key to accept that segment.
7.
Repeat Step 6 for each remaining segment.
8.
Scroll to
TCP/IP Network Mask
by pressing the
Up Arrow
or
Down Arrow
key.
9.
By pressing the
Up Arrow
or
Down Arrow
key, scroll to the correct number for the first segment
of the address. Press the
OK
key to accept that segment.
10.
Repeat Step 9 for each remaining segment.
11.
Scroll to
TCP/IP Gateway
by pressing the
Up Arrow
or
Down Arrow
key.
12.
Scroll to the correct number for the first segment of the address by pressing the
Up Arrow
or
Down Arrow
key. Press the
OK
key to accept that segment.
13.
Repeat Step 12 for each remaining segment.
14.
To exit the menu system, scroll to
Exit
and press the
OK
key.
Information Required for IP Addressing
Information
Comments
Internet (IP) address for the printer
Format is
xxx.xxx.xxx.xxx
, where
xxx
represents a decimal number
from 0 - 255.
Network Mask
If you are unsure, leave this blank; the printer chooses an
appropriate mask.
Default Router/Gateway address
If you want to communicate with the printer from anywhere other
than the local network segment, you need the router address.