Xerox 8560DN User Guide - Page 146

Operational Safety

Get Xerox 8560DN - Phaser Color Solid Ink Printer PDF manuals and user guides
UPC - 095205733280
View all Xerox 8560DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Operational Safety Your printer and supplies were designed and tested to meet strict safety requirements. These include safety agency examination, approval, and compliance with established environmental standards. Your attention to the following safety guidelines helps to ensure the continued, safe operation of your printer. Printer Location ■ Place the printer in a dust-free area within a temperature range of 50° F to 90° F (10° C to 32° C) and a relative humidity range of 10 percent to 80 percent. ■ Place the printer in an area where there is adequate space for ventilation, operation, and servicing. ■ Do not place the printer on a carpeted floor. Airborne carpet fibers can be pulled into the printer and cause print-quality problems. ■ Do not place the printer near a heat source. ■ Do not place the printer in direct sunlight to avoid exposure to light-sensitive components. ■ Do not place the printer where it is directly exposed to the cold air flow from an air conditioning system. ■ Do not place the printer on a file cabinet. Closing file cabinet drawers causes jarring and can create light stripes in prints. Printer Clearance The recommended minimal spacing is: ■ 20.00 cm (7.5 in.) above the printer ■ 10.16 cm (4.0 in.) behind the printer ■ 10.16 cm (4.0 in.) on the left side of the printer ■ 40.00 cm (15.5 in.) on the right side of the printer to allow access to the maintenance kit and waste tray Operational Guidelines ■ Do not block or cover the slots and openings on the printer. The printer can overheat without adequate ventilation. ■ Use the printer at elevations below 2,438 m (8,000 ft.). ■ Place the printer on a level, solid, non-vibrating surface with adequate strength to hold the weight of the printer. The base printer weight, without any packaging materials, is approximately 28 kg (60 lb.). The printer should be within 2° horizontal with all four feet in solid contact with the surface. Phaser® 8560 Color Printer A-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
Phaser® 8560 Color Printer
A-3
Operational Safety
Your printer and supplies were designed and tested to meet strict safety requirements. These
include safety agency examination, approval, and compliance with established environmental
standards.
Your attention to the following safety guidelines helps to ensure the continued, safe operation
of your printer.
Printer Location
■
Place the printer in a dust-free area within a temperature range of 50° F to 90° F (10° C to
32° C) and a relative humidity range of 10 percent to 80 percent.
■
Place the printer in an area where there is adequate space for ventilation, operation, and
servicing.
■
Do not place the printer on a carpeted floor. Airborne carpet fibers can be pulled into the
printer and cause print-quality problems.
■
Do not place the printer near a heat source.
■
Do not place the printer in direct sunlight to avoid exposure to light-sensitive components.
■
Do not place the printer where it is directly exposed to the cold air flow from an air
conditioning system.
■
Do not place the printer on a file cabinet. Closing file cabinet drawers causes jarring and
can create light stripes in prints.
Printer Clearance
The recommended minimal spacing is:
■
20.00 cm (7.5 in.) above the printer
■
10.16 cm (4.0 in.) behind the printer
■
10.16 cm (4.0 in.) on the left side of the printer
■
40.00 cm (15.5 in.) on the right side of the printer to allow access to the maintenance kit
and waste tray
Operational Guidelines
■
Do not block or cover the slots and openings on the printer. The printer can overheat
without adequate ventilation.
■
Use the printer at elevations below 2,438 m (8,000 ft.).
■
Place the printer on a level, solid, non-vibrating surface with adequate strength to hold the
weight of the printer. The base printer weight, without any packaging materials, is
approximately 28 kg (60 lb.). The printer should be within 2° horizontal with all four feet
in solid contact with the surface.