Yamaha CL3 Cl Editor Owner's Manual - Page 3

Mixer Setup, Set Default, Mix Bus Setup

Get Yamaha CL3 PDF manuals and user guides View all Yamaha CL3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

9 Set Default Press this button to use the settings (except for the IP Address in the Network section) currently specified in the System Setup dialog box as the default settings. The next time when you start up CL Editor, it will use these settings. ❏ Mixer Setup To open the Mixer Setup dialogbox, choose [Mixer Setup] from the [File] menu. 1 Mix Bus Setup Here you can make settings relating to the MIX buses. Signal Type: Choose either MONOx2 or STEREO for each 1 two adjacent odd-numbered/even-numbered MIX buses. Bus Type/Send Point: Choose either VARI (PRE FADER) or VARI (PRE EQ) or FIXED for each two adjacent odd-numbered/even-numbered MIX buses. Pan Link: The PAN setting for signals sent to stereo MIX buses will link to the PAN setting for the STEREO bus. This parameter is valid only if the Signal Type is set to STEREO and the Bus Type is set to VARI. 2 Matrix Bus Setup Here you can make settings relating to the MATRIX buses. Signal Type: Choose either MONOx2 or STEREO for each 2 two adjacent odd-numbered/even-numbered MATRIX buses. Send Point for Input Channels: Choose either PRE FADER or PRE EQ for each two adjacent odd-numbered/ even-numbered MATRIX buses. Pan Link: The PAN setting for signals sent to stereo MATRIX buses will link to the PAN setting for the STEREO bus. This parameter is valid only if the Signal Type is set to STEREO. 3 CL Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
CL Editor Owner’s Manual
3
9
Set Default
Press this button to use the settings (except for the IP Address in the Network section) currently specified in the System
Setup dialog box as the default settings. The next time when you start up CL Editor, it will use these settings.
❏
Mixer Setup
To open the Mixer Setup dialogbox, choose [Mixer Setup] from the [File] menu.
1
Mix Bus Setup
Here you can make settings relating to the MIX buses.
Signal Type:
Choose either MONOx2 or STEREO for each
two adjacent odd-numbered/even-numbered MIX buses.
Bus Type/Send Point:
Choose either VARI (PRE
FADER) or VARI (PRE EQ) or FIXED for each two adjacent
odd-numbered/even-numbered MIX buses.
Pan Link:
The PAN setting for signals sent to stereo MIX
buses will link to the PAN setting for the STEREO bus. This
parameter is valid only if the Signal Type is set to STEREO
and the Bus Type is set to VARI.
2
Matrix Bus Setup
Here you can make settings relating to the MATRIX buses.
Signal Type:
Choose either MONOx2 or STEREO for each
two adjacent odd-numbered/even-numbered MATRIX
buses.
Send Point for Input Channels:
Choose either PRE
FADER or PRE EQ for each two adjacent odd-numbered/
even-numbered MATRIX buses.
Pan Link:
The PAN setting for signals sent to stereo
MATRIX buses will link to the PAN setting for the STEREO
bus. This parameter is valid only if the Signal Type is set to STEREO.
1
2