Yamaha CSP-150 CSP-170/CSP-150 Owners Manual - Page 37

Set the adjuster., Attach the headphone hanger., Attach F to A. - review

Get Yamaha CSP-150 PDF manuals and user guides View all Yamaha CSP-150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

 Use a vinyl tie to take up any slack in the pedal cord.  Insert the plug of the power cord into the power connector. 6 Set the adjuster. Rotate the adjuster until it comes in firm contact with the floor surface.  Install the brackets of F onto J, and slide them so that J fit into the smaller ends of the keyhole slots. F  A F 7 Attach the headphone hanger. Use L (x 2) to attach the hanger as shown in the illustration. L 8 Attach F to A.  Finger-tighten J (x 2) as shown in the illustration.  J Approx. 5 mm A  A  Fully tighten J. After completing the assembly, please check the following. • Are there any parts left over? → Review the assembly procedure and correct any errors. • Is the instrument clear of doors and other movable fixtures? → Move the instrument to an appropriate location. • Do the instrument or the music rest make a rattling noise when you shake it? → Tighten all screws. • Does the pedal box rattle or give way when you step on the pedals? → Turn the adjuster so that it is set firmly against the floor. • Are the pedal and power cords inserted securely into the sockets? → Check the connection. Assembly CSP-170/CSP-150 Owner's Manual 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
CSP-170/CSP-150 Owner’s Manual
37
Assembly
3
Use a vinyl tie to take up any slack in the pedal cord.
4
Insert the plug of the power cord into the power connector.
6
Set the adjuster.
Rotate the adjuster until it comes in firm contact with the
floor surface.
7
Attach the headphone hanger.
Use L (x 2) to attach the hanger as shown in the
illustration.
8
Attach F to A.
1
Finger-tighten J (x 2) as shown in the illustration.
2
Install the brackets of F onto J, and slide them so that J fit into
the smaller ends of the keyhole slots.
3
Fully tighten J.
L
1
J
A
Approx. 5 mm
After completing the assembly, please check the following.
•
Are there any parts left over?
→ Review the assembly procedure and correct any errors.
•
Is the instrument clear of doors and other movable
fixtures?
→ Move the instrument to an appropriate location.
•
Do the instrument or the music rest make a rattling
noise when you shake it?
→ Tighten all screws.
•
Does the pedal box rattle or give way when you step on
the pedals?
→ Turn the adjuster so that it is set firmly against the floor.
•
Are the pedal and power cords inserted securely into
the sockets?
→ Check the connection.
A
F
2
A
F
3