Yamaha HTR-3069 HTR-3069 Owner s Manual - Page 27

Error messages

Get Yamaha HTR-3069 PDF manuals and user guides View all Yamaha HTR-3069 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Error messages If any error message is displayed during the measurement, resolve the problem and perform YPAO again. Auto Setup ERROR E-9 : User Cancel < RETRY > Error message 2 % TV screen CHARGE ENHANCER STEREO TUNED OUT ECO E-5:NOISY Front display SLEEP MUTE VOL. ADAPTIVE DRC VIRTUAL n Procedure to handle errors 1 Check the content of error message and press ENTER. 2 Use the cursor keys (e/r) to select the desired operation. To exit the YPAO measurement: 1 Select "EXIT" and press ENTER. 2 Use the cursor keys (q/w) to select "Exit" and press ENTER. 3 Disconnect the YPAO microphone from the unit. To retry the YPAO measurement from beginning: 1 Select "RETRY" and press ENTER. To proceed with the current YPAO measurement (for E-5 and E-9 only): 1 Select "PROCEED" and press ENTER. Error message E-1:No Front SP (E-1:NO FRNT SP) E-2:No Sur. SP (E-2:NO SUR SP) E-5:Noisy (E-5:NOISY) E-7:No MIC (E-7:NO MIC) E-8:No Signal (E-8:NO SIGNAL) E-9:User Cancel (E-9:CANCEL) E-10:Internal Err. (E-10:INTERNAL) Cause Remedy Front speakers are not detected. One of the surround speakers cannot be detected. Exit YPAO, turn off the unit, and then check the speaker connections. The noise is too loud. Keep the room quiet and retry YPAO. If you select "PROCEED", YPAO takes the measurement again and ignores any noise detected. The YPAO microphone has Connect the YPAO microphone to the been removed. YPAO MIC jack firmly and retry YPAO. The YPAO microphone cannot detect test tones. Connect the YPAO microphone to the YPAO MIC jack firmly and retry YPAO. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. The measurement has been canceled. Retry or exit YPAO as necessary. An internal error has occurred. Exit YPAO, and turn off and on the unit. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. Note Texts in parentheses denote indicators on the front display. 27 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Error messages
If any error message is displayed during the measurement, resolve the problem and
perform YPAO again.
Auto Setup
ERROR
E-9 : User Cancel
<
RETRY
>
2 %
Error message
TV screen
MUTE
ENHANCER
STEREO
TUNED
SLEEP
OUT
ECO
CHARGE
ADAPTIVE DRC
VIRTUAL
E-5:NOISY
VOL.
Front display
n
Procedure to handle errors
1
Check the content of error message and press ENTER.
2
Use the cursor keys (
e
/
r
) to select the desired operation.
To exit the YPAO measurement:
1
Select “EXIT” and press ENTER.
2
Use the cursor keys (
q
/
w
) to select “Exit” and press ENTER.
3
Disconnect the YPAO microphone from the unit.
To retry the YPAO measurement from beginning:
1
Select “RETRY” and press ENTER.
To proceed with the current YPAO measurement (for E-5 and E-9
only):
1
Select “PROCEED” and press ENTER.
Error message
Cause
Remedy
E-1:No Front SP
(E-1:NO FRNT SP)
Front speakers are not
detected.
Exit YPAO, turn off the unit, and then
check the speaker connections.
E-2:No Sur. SP
(E-2:NO SUR SP)
One of the surround
speakers cannot be
detected.
E-5:Noisy
(E-5:NOISY)
The noise is too loud.
Keep the room quiet and retry YPAO. If
you select “PROCEED”, YPAO takes the
measurement again and ignores any
noise detected.
E-7:No MIC
(E-7:NO MIC)
The YPAO microphone has
been removed.
Connect the YPAO microphone to the
YPAO MIC jack firmly and retry YPAO.
E-8:No Signal
(E-8:NO SIGNAL)
The YPAO microphone
cannot detect test tones.
Connect the YPAO microphone to the
YPAO MIC jack firmly and retry YPAO. If
this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or
service center.
E-9:User Cancel
(E-9:CANCEL)
The measurement has been
canceled.
Retry or exit YPAO as necessary.
E-10:Internal Err.
(E-10:INTERNAL)
An internal error has
occurred.
Exit YPAO, and turn off and on the unit. If
this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or
service center.
Note
Texts in parentheses denote indicators on the front display.
En
27