Yamaha HTR 6250 Owner's Manual - Page 45

INTRODUCTION PREPARATION BASIC OPERATION ADVANCED OPERATION ■ B)Level Adjustable range: -10.0dB to +10.0dB (0.5 dB step) Defaults: "FR.L/FR.R/SWFR" 0dB* "CNTR/SUR.L/SUR.R/SBL/SBR" -1.0dB Separately adjusts volume of each speaker so that the sounds form speakers are at the same volume at the listening position. Items to be displayed vary depending on the number of speakers connected. y • When only one surround back speaker is connected, "SB" appears instead of "SBL" and "SBR." • You can adjust the volume listening to test tones when you set "Test Tone" to "On" (see page 41). • If your subwoofer has a volume control or a crossover frequency control, set the volume to half or the crossover frequency at the maximum. ■ C)Distance Adjusts timing at which each speaker outputs sound so that sounds from speakers reach the listening position at the same time. Set unit (Unit) first and set the distance of each speaker. Unit Choices: meters (m)/feet (ft)* meters (m) Displays the speaker distance in meters. feet (ft) Displays the speaker distance in feet. Front L / Front R / Center / Sur. L / Sur. R / Sur.B L / Sur.B R / SWFR Adjustable range: 0.30m to 24.00m (1.0ft to 80.0ft) Defaults: 3.00m (10.0ft) "Front L/Front R/ SWFR" 2.60m (8.5ft) "Center" 2.40m (8.0ft) "Sur. L/Sur. R/ Sur.B L/Sur.B R" y • Different items are displayed depending on settings of "A)Config" (see page 39). • When only one surround back speaker is connected, "Sur.B" appears instead of "Sur.B L" and "Sur.B R." ■ D)Equalizer Adjusts sound quality and tone using a parametric graphic equalizer. EQ Type Select Choices: Auto PEQ/GEQ*/Off Select an equalizer type. Auto PEQ GEQ Off Uses a parametric equalizer selected in "Auto Setup." Characteristics of the currently used parametric equalizer (see page 18) are displayed below "Auto PEQ." Uses a graphic equalizer. Press nENTER to adjust the characteristics of the graphic equalizer. Not use a graphic equalizer. Operating various settings for this unit (Setup menu) GEQ Choices: 63Hz/160Hz/400Hz/1kHz/2.5kHz/ 6.3kHz/16kHz Adjustable range: -6.0dB to 0dB* to +6.0dB (0.5 dB step) Adjusts sound quality of each speaker using a graphic equalizer. The graphic equalizer of this unit can adjust signal levels in 7 frequency ranges. To adjust the signal level in each range, select the desired speaker with nCursor l / h while "→" is displayed next to "Channel," then select the desired frequency band with nCursor k / n, and adjust the signal level with nCursor l / h. ■ E)Test Tone Choices: Off*/On Switches between on and off of an oscillator that generates test tones. To turn on the oscillator, select "On" using nCursor l / h. When "On" is selected, you can adjust the settings of "2 Manual Setup" while listening to a test tone. Off Not generate test tones. On Generates test tones. Sound Setup You can set various items for sound outputs. ■ 1 Dynamic Range Choices: Min/Auto/STD/Max* Selects the dynamic range adjustment method for reproducing bitstream signals. Min/Auto STD Max (Min) Sets the dynamic range suitable for low volume or a quiet environment, such as at night, for bitstream signals except for Dolby TrueHD signals. (Auto) Adjusts the dynamic range for Dolby TrueHD signals based on input signal information. Sets the standard dynamic range recommended for regular home use. Outputs sound without adjusting the dynamic range of the input signals. ■ 2 Lipsync Adjusts delay between video output and audio output. HDMI Auto Choices: Off*/On Automatically adjusts output timing of audio and video signals when a monitor that supports an automatic lipsync function is connected to this unit. Off Select this when the connected monitor does not support the automatic lip-sync function or you do not use the automatic lip-sync function. Set the correction time in "Manual Delay." On Select this when the connected monitor supports the automatic lip-sync function. Fine adjust the correction time in "Auto Delay." ADDITIONAL INFORMATION APPENDIX English 41 En