Yamaha LS9-32 Owner's Manual - Page 63
Use the MIX/MATRIX SELECT keys, DPRE/POST indicator
View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 63 highlights
Sending the signal from an input channel to a MIX bus D PRE/POST indicator This indicates the send position of the signal sent from the input channel to a VARI type MIX bus. The signal is being sent from the pre-EQ or pre-fader position if this indicates PRE, or from immediately after the [ON] key if the PRE indication is not shown. This indicator is only for display. You cannot use this field to change the send position of the signal. 3 Use the LAYER section keys and the [SEL] keys of the channel module section or ST IN section to select the input channel that you want to operate. 4 Use the MIX/MATRIX SELECT section keys to select the send-destination MIX bus. The LED of the corresponding key will light, indicating that it is selected as the send-destination. ● If the send-destination MIX bus is the VARI type The TO MIX field in the screen shows the knob in the same color as the corresponding key of the MIX/ MATRIX SEND section. ● If the send-destination MIX bus is the FIXED type The TO MIX field will show the TO MIX ON/OFF button instead of the TO MIX LEVEL knob. In this case, you can't adjust the send level. NOTE • If the LED of only a specific key in the MIX/MATRIX SELECT section is blinking and the LEDs of the remaining keys are lit, the LS9 is in SENDS ON FADER mode (the mode in which you can use the faders to control the send levels to the MIX buses or MATRIX buses). Press the desired key in the MIX/ MATRIX SELECT section so that only the LED of that key is lit. 5 If you selected a VARI type MIX bus in step 4, use the SELECTED CHANNEL section [SELECTED SEND] encoder to adjust the send level from that channel to the MIX bus you selected in step 4. If the send-destination MIX bus is set to stereo, the function of the [SELECTED SEND] encoder will change depending on which of the two adjacent keys of the MIX/MATRIX SELECT section are lit. ● If the left key is lit Use the [SELECTED SEND] encoder to adjust the 5 pan (or balance, for a ST IN channel) of the signal that is sent from the INPUT channel to the two MIX buses. ● If the right key is lit Use the [SELECTED SEND] encoder to adjust the send level shared by the two MIX buses. 6 To switch the on/off status of a signal sent to a VARI type MIX bus, move the cursor to the TO MIX LEVEL knob in the screen and press the [ENTER] key to accsess the MIX SEND popup window. If you switch this off, the knob will turn grey. 7 To switch the on/off status of a signal sent to a FIXED type MIX bus, move the cursor to the TO MIX ON/OFF button in the screen and press the [ENTER] key. If you switch this off, the knob will change to black characters on a blue background. To turn it back on, press the [ENTER] key once again. 8 Use the top panel [SEL] keys to select another input channel, and adjust the send level to the selected MIX bus in the same way. 9 Use the keys of the MIX/MATRIX SELECT section to select another MIX bus as the send-destination, and adjust the send level from the input channel in the same way. HINT • If PRE is selected as the send position to the MIX bus, then you will also be able to select either PRE EQ (immediately before the attenuator) or PRE FADER (immediately before the fader) for each MIX bus (→ p. 213). • If desired, the pan/balance setting of the signal sent to a stereo MIX bus can be linked with the TO ST PAN/TO ST BAL knob of the SELECTED CH VIEW screen (→ p. 213). • If you want to monitor the signal that is being sent to a specific MIX bus, select the master fader layer and press the [CUE] key for that MIX channel. Input channel operations LS9-16/32 Owner's Manual 63