Yamaha M7CL M7cl V3 Editor Owner's Manual (v3.0.x) - Page 18

KPAN/TO STEREO MONO LSEL Select MCUE NON OFader, PAN knob, ST] button - monitor console

Get Yamaha M7CL PDF manuals and user guides View all Yamaha M7CL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

K PAN/TO STEREO MONO The PAN knob adjusts the panning of the signal that is sent from the INPUT CH to the K STEREO bus L/R channels (or the L/C/R channels). You can set this to the center value by holding down the (< >) key of your computer keyboard and clicking this L knob. M The [ST] button is an on/off switch for the signal that is sent from the INPUT CH to the STEREO bus. N The [M(C)] button is an on/off switch for the signal that is sent from the INPUT CH to the MONO bus. If LCR MODE is selected in the Selected Channel window, the [LCR] button will appear instead of the [ST] button and [M(C)] button, and the [LCR] button will be an on/off switch for the signal that is sent from the INPUT CH to the LCR bus. O L SEL (Select) Selects the INPUT CH for which you want to perform operations. This is linked with the INPUT section [SEL] keys on the M7CL console panel. NOTE If the Channel Select / Sends On Fader checkbox in the System Setup dialog box is not checked, this will not be linked with the M7CL console. M CUE P This button cue-monitors the signal of the INPUT CH. This is linked with the INPUT section [CUE] keys on the M7CL's panel. Q NOTE If the Channel Select / Sends On Fader checkbox in the System Setup dia- log box is not checked, this will not be linked with the M7CL console. N ON Switches the INPUT CH or send on/off. In normal mode, this button is linked with the CH [ON] key in the INPUT section on the M7CL console panel. The button is color-coded and indicates status as follows: White: INPUT CH is on (normal mode) Gray: INPUT CH/Send are off. Other colors: Send is on (SENDS ON FADER mode). NOTE If the Channel Select / Sends On Fader checkbox in the System Setup dialog box is not checked, this will not be linked with the M7CL console. O Fader Adjusts the input level of the INPUT CH, or the send level. In normal mode, this fader is linked with the fader in the INPUT section on of the M7CL console panel. The fader is color-coded and indicates status as follows: White: You can adjust the input level of the INPUT CH (normal mode). Gray: INPUT CH is off. Other colors: You can adjust the send level (SENDS ON FADER mode). The current fader value is shown in the numerical box located immediately below the fader. You can set this to the minimum value (-∞ dB) by holding down the (< >) key of your computer keyboard and clicking the fader knob, or set it to the nominal value (0.00 dB) by holding down the (< >) key and key and clicking the fader knob. 18 M7CL V3 Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
M7CL V3 Editor Owner’s Manual
18
K
PAN/TO STEREO MONO
The
PAN knob
adjusts the panning of the signal that is sent from the INPUT CH to the
STEREO bus L/R channels (or the L/C/R channels). You can set this to the center value
by holding down the <Ctrl>(<
>) key of your computer keyboard and clicking this
knob.
The
[ST] button
is an on/off switch for the signal that is sent from the INPUT CH to
the STEREO bus.
The
[M(C)] button
is an on/off switch for the signal that is sent from the INPUT CH to
the MONO bus.
If LCR MODE is selected in the Selected Channel window, the
[LCR]
button will appear
instead of the [ST] button and [M(C)] button, and the [LCR] button will be an on/off
switch for the signal that is sent from the INPUT CH to the LCR bus.
L
SEL (Select)
Selects the INPUT CH for which you want to perform operations. This is linked with
the INPUT section [SEL] keys on the M7CL console panel.
If the Channel Select / Sends On Fader checkbox in the System Setup dia-
log box is not checked, this will not be linked with the M7CL console.
M
CUE
This button cue-monitors the signal of the INPUT CH. This is linked with the INPUT
section [CUE] keys on the M7CL’s panel.
If the Channel Select / Sends On Fader checkbox in the System Setup dia-
log box is not checked, this will not be linked with the M7CL console.
N
ON
Switches the INPUT CH or send on/off. In normal mode, this button is linked with the
CH [ON] key in the INPUT section on the M7CL console panel.
The button is color-coded and indicates status as follows:
White:
INPUT CH is on (normal mode)
Gray:
INPUT CH/Send are off.
Other colors: Send is on (SENDS ON FADER mode).
If the Channel Select / Sends On Fader checkbox in the System Setup dia-
log box is not checked, this will not be linked with the M7CL console.
O
Fader
Adjusts the input level of the INPUT CH, or the send level. In normal mode, this fader
is linked with the fader in the INPUT section on of the M7CL console panel.
The fader is color-coded and indicates status as follows:
White:
You can adjust the input level of the INPUT CH (normal mode).
Gray:
INPUT CH is off.
Other colors: You can adjust the send level (SENDS ON FADER mode).
The current fader value is shown in the numerical box located immediately below the
fader.
You can set this to the minimum value (–
∞
dB) by holding down the <Ctrl>(<
>) key
of your computer keyboard and clicking the fader knob, or set it to the nominal value
(0.00 dB) by holding down the <Ctrl>(<
>) key and <Shift> key and clicking the
fader knob.
L
M
N
P
O
Q
K
NOTE
NOTE
NOTE