Yamaha M7CL M7cl V3 Editor Owner's Manual (v3.0.x) - Page 41

ST/MONO button, LCR button, When this button is

Get Yamaha M7CL PDF manuals and user guides View all Yamaha M7CL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

HINT • If you are using MATRIX buses in stereo, the knob for the odd-numbered bus will be PAN. • The stereo/mono status can be specified in the Mixer Setup dialogbox. Knob of oddnumbered side ❏ TO STEREO/MONO Here you can specify how the signal will be sent from the MIX channel to the STEREO bus / MONO bus. MODE • ST/MONO button When this button is on, the signal will be sent to the STEREO bus and independently to the MONO bus. PAN ST MONO BALANCE Adjusts the panning of the signal sent from the MIX channel to the STEREO bus L/R channels. You can set this to the center position by holding down the (< >) key of the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the M7CL panel. If the selected MIX bus is used as a stereo bus, the odd-numbered channel is fixed at L63 and the even-numbered channel fixed at R63. Switches the signal sent from the MIX channel to the STEREO bus on/off. Switches the signal sent from the MIX channel to the MONO bus on/off. This is shown only if the selected MIX bus is assigned as a stereo bus. It adjusts the left/ right volume balance of the stereo bus. You can set this to the center position by holding down the (< >) key of the computer keyboard and clicking the knob. • LCR button When this button is on, the signal will be sent to the L/C/R buses which work in conjunction with each other. PAN BALANCE CSR (Center Side Ratio) Adjusts the panning of the signal that is sent from the MIX channel to each of the L/C/R channels. You can set this to the center position by holding down the (< >) key of the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the M7CL panel. If the selected MIX bus is used as a stereo bus, the odd-numbered channel is fixed at L63 and the even-numbered channel fixed at R63. This is shown only if the selected MIX bus is assigned as a stereo bus. It adjusts the left/ right volume balance of the stereo bus. You can set this to the center position by holding down the (< >) key of the computer keyboard and clicking the knob. Adjusts the proportion of the CENTER channel level relative to the STEREO bus L/R in a range of 0-100%. 41 M7CL V3 Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
M7CL V3 Editor Owner’s Manual
41
•
If you are using MATRIX buses in stereo, the knob for the odd-numbered bus will
be PAN.
•
The stereo/mono status can be specified in the Mixer Setup dialogbox.
❏
TO STEREO/MONO
Here you can specify how the signal will be sent from the MIX channel to the STEREO bus / MONO bus.
MODE
•
ST/MONO button
When this button is on, the signal will be sent to the STEREO bus and independently to the MONO bus.
•
LCR button
When this button is on, the signal will be sent to the L/C/R buses which work in conjunction with each other.
PAN
Adjusts the panning of the signal sent from the MIX channel to the STEREO bus L/R chan-
nels. You can set this to the center position by holding down the <Ctrl>(<
>) key of the
computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the
SELECTED CHANNEL section of the M7CL panel. If the selected MIX bus is used as a ste-
reo bus, the odd-numbered channel is fixed at L63 and the even-numbered channel fixed at
R63.
ST
Switches the signal sent from the MIX channel to the STEREO bus on/off.
MONO
Switches the signal sent from the MIX channel to the MONO bus on/off.
BALANCE
This is shown only if the selected MIX bus is assigned as a stereo bus. It adjusts the left/
right volume balance of the stereo bus. You can set this to the center position by holding
down the <Ctrl>(<
>) key of the computer keyboard and clicking the knob.
PAN
Adjusts the panning of the signal that is sent from the MIX channel to each of the L/C/R
channels. You can set this to the center position by holding down the <Ctrl>(<
>) key of
the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the
SELECTED CHANNEL section of the M7CL panel. If the selected MIX bus is used as a ste-
reo bus, the odd-numbered channel is fixed at L63 and the even-numbered channel fixed at
R63.
BALANCE
This is shown only if the selected MIX bus is assigned as a stereo bus. It adjusts the left/
right volume balance of the stereo bus. You can set this to the center position by holding
down the <Ctrl>(<
>) key of the computer keyboard and clicking the knob.
CSR (Center Side Ratio)
Adjusts the proportion of the CENTER channel level relative to the STEREO bus L/R in a
range of 0–100%.
HINT
Knob of odd-
numbered side