Yamaha MCX-2000 MCXSP10 Manual - Page 124

Troubleshooting Refer to the chart below when the MCX-2000 doesn't appear to be functioning correctly. If the problem you are experiencing is not listed below or if the instructions listed next to the problem don't help, set the MCX-2000 to standby mode, disconnect the power cable from the AC outlet, and contact the nearest authorized YAMAHA dealer or service center. Symptom Cause The MCX-2000 does not turn on when The MusicCAST power plug is not you press STANDBY/ON. inserted into the AC outlet correctly. The MCX-2000 does not play CDs. There is condensation on the laser pickup lens. The MCX-2000 cannot store CDs. The CD is loaded upside-down in the disc tray. The CD is dirty. There is no space remaining on the hard disk drive. The CD-R/RW loaded in the MCX-2000 is dirty or scratched. The MCX-2000 cannot record songs to The CD-R/RW loaded in the a CD-R/RW. MCX-2000 already has data recorded on it. Remedy Insert the power plug firmly into an AC outlet. Turn off the power, wait 20 or 30 minutes, and then turn power on again. Load the CD in the disc tray label side up. Clean the CD. Delete songs that you do not need, to make space on the hard disk drive. Clean or replace the CD-R/RW. Load a blank audio CD-R/RW into the disc tray. The CD-R/RW loaded in the MCX-2000 is dirty or scratched. For CD-Rs, replace the CD-R with a new disc. For CD-RWs, initialize the disc and then record it again. The MCX-2000 will not record songs longer than 100 minutes in duration on its hard disk drive. The maximum length for a single song is 99 minutes and 59 seconds. The MCX-2000 begins recording a new song after recording for 99 minutes and 59 seconds, regardless of the recording mode set There is a pause starting playback of songs when the MCX-2000 is connected to an amplifier via a digital connection. The MCX-2000 is playing back tracks recorded with differing emphasis settings. Connect the analog outputs on the MCX-2000 to the amplifier. CD-R/RW made on the MCX-2000 will not playback correctly on other CD or DVD players. The CD or DVD player you are using is not capable of Use a CD/DVD player capable of playing back playing CD-R/RW. CD-R/RW. Sound from the MCX-2000 skips during playback. Either the MCX-2000 or the source component is being shaken or vibrated. Change the location of your components (unless the source recording was affected by vibrations or shocks). The CD is dirty. Clean the disc. The MCX-2000 does not operate normally. The system controller has stopped. Press and hold the STANDBY/ON button on the front panel for at least 15 seconds. You can hear the sound of a fan coming The internal temperature of the from the MCX-2000. MCX-2000 is rising. The internal fan in the MCX-2000 activates when the internal temperature of the unit rises. This is not a malfunction. Auto Configuration does not function correctly. The network settings are incorrect. Surroundings are interfering with wireless network signals (for wireless connections only). Check the network settings. Change the location of MusicCAST components. Try using a different wireless network channel. Use wired network connections to connect MusicCAST components. Either the MCX-2000 or the MCX-A10 is not set to Auto Configuration mode. Check the connection procedure and try again. The client is storing or recording songs. Try again when recording is complete. You cannot start playback on the clients. Configuration has not finished. The network settings are incorrect. Carry out the Auto Configuration process. Check the network settings. There are no songs which the MCX-2000 has finished Wait until MP3 encoding is complete. encoding to MP3 format in the MCX-2000 library. Surroundings are interfering with wireless network signals (for wireless connections only). Change the location of MusicCAST components. Try using a different wireless network channel. Use wired network connections to connect MusicCAST components. 108 MCX-2000 Owner's Manual