Yamaha RX-V475 RX-V575/RX-V475 Owners Manual - Page 94

Video, FM/AM radio, The menu of the unit is not displayed on the TV.

Get Yamaha RX-V475 PDF manuals and user guides View all Yamaha RX-V475 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Video Problem No video. Cause Another input source is selected on the unit. Another input source is selected on the TV. The video signal output from the unit is not supported by the TV. The cable connecting the unit and TV (or playback device) is defective. The input video signal (resolution) is not supported by the unit. No video from the playback device (connected to the unit with HDMI). The TV does not support HDCP (High-bandwidth Digital Content Protection). The number of devices connected to the HDMI OUT jack is over the limit. The menu of the unit is not displayed on the TV. The TV is not connected to the unit via HDMI. Another input source is selected on the TV. Remedy Select an appropriate input source with the input selection keys. Switch the TV input to display the video from the unit. Check the video output setting of the playback device. For information about video signals supported by the TV, refer to the instruction manuals for the TV. If there is no problem with the connection, replace with another cable. To check the information about the current video signal (resolution), use "Signal Info" in the "Option" menu (p.66). For information about video signals supported by the unit, see "HDMI signal compatibility" (p.102). Refer to the instruction manuals for the TV and check the TV's specifications. Disconnect some of the HDMI devices. You can display the menu of the unit on the TV only when they are connected with an HDMI cable. If necessary, use an HDMI cable to connect them (p.18 to 21). Switch the TV input to display the video from the unit (HDMI OUT jack). FM/AM radio Problem FM radio reception is weak or noisy. Cause There is multi-path interference. Your area is too far from the FM station transmitter. AM radio reception is weak or noisy. The noises may be caused by fluorescent lamps, motors, thermostats, or other electrical equipment. Your area is too far from the FM station transmitter. Radio stations cannot be selected automatically. The AM radio signal is weak. AM radio stations cannot be registered as presets. Auto Preset has been used. Remedy Adjust the FM antenna height or orientation, or place it in a different location. Press MODE to select monaural FM radio reception (p.43). Use an outdoor FM antenna. We recommend using a sensitive multi-element antenna. It is difficult to completely eliminate noise. It may be reduced by using an outdoor AM antenna. Select the station manually (p.43). Use an outdoor antenna. We recommend using a sensitive multi-element antenna. Adjust the AM antenna orientation. Select the station manually (p.43). Use an outdoor AM antenna. Connect it to the ANTENNA (AM) jack together with the supplied AM antenna. Auto Preset is for registering FM radio stations only. Register AM radio stations manually (p.44). APPENDIX ➤ Troubleshooting En 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
APPENDIX
➤
Troubleshooting
En
94
Video
FM/AM radio
Problem
Cause
Remedy
No video.
Another input source is selected on the unit.
Select an appropriate input source with the input selection keys.
Another input source is selected on the TV.
Switch the TV input to display the video from the unit.
The video signal output from the unit is not supported by the TV.
Check the video output setting of the playback device. For information about
video signals supported by the TV, refer to the instruction manuals for the TV.
The cable connecting the unit and TV (or playback device) is
defective.
If there is no problem with the connection, replace with another cable.
No video from the playback device (connected to
the unit with HDMI).
The input video signal (resolution) is not supported by the unit.
To check the information about the current video signal (resolution), use “Signal
Info” in the “Option” menu (p.66). For information about video signals supported
by the unit, see “HDMI signal compatibility” (p.102).
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
Refer to the instruction manuals for the TV and check the TV’s specifications.
The number of devices connected to the HDMI OUT jack is over
the limit.
Disconnect some of the HDMI devices.
The menu of the unit is not displayed on the TV.
The TV is not connected to the unit via HDMI.
You can display the menu of the unit on the TV only when they are connected with
an HDMI cable. If necessary, use an HDMI cable to connect them (p.18 to 21).
Another input source is selected on the TV.
Switch the TV input to display the video from the unit (HDMI OUT jack).
Problem
Cause
Remedy
FM radio reception is weak or noisy.
There is multi-path interference.
Adjust the FM antenna height or orientation, or place it in a different location.
Your area is too far from the FM station transmitter.
Press MODE to select monaural FM radio reception (p.43).
Use an outdoor FM antenna. We recommend using a sensitive multi-element
antenna.
AM radio reception is weak or noisy.
The noises may be caused by fluorescent lamps, motors,
thermostats, or other electrical equipment.
It is difficult to completely eliminate noise. It may be reduced by using an outdoor
AM antenna.
Radio stations cannot be selected automatically.
Your area is too far from the FM station transmitter.
Select the station manually (p.43).
Use an outdoor antenna. We recommend using a sensitive multi-element
antenna.
The AM radio signal is weak.
Adjust the AM antenna orientation.
Select the station manually (p.43).
Use an outdoor AM antenna. Connect it to the ANTENNA (AM) jack together with
the supplied AM antenna.
AM radio stations cannot be registered as
presets.
Auto Preset has been used.
Auto Preset is for registering FM radio stations only. Register AM radio stations
manually (p.44).