Yamaha RX-V863 Owner's Manual - Page 32

Connecting the power cable, Setting the speaker impedance, AC OUTLETS SWITCHED - specifications

Get Yamaha RX-V863 PDF manuals and user guides View all Yamaha RX-V863 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Connections Connecting the power cable Setting the speaker impedance (U.S.A. model) MONITOR OUT AC OUTLETS SWITCHED 120V 80Hz 100W MAX. TOTAL 0.8A MAX. TOTAL C DVR To the AC wall outlet Caution If you are to use 6 ohm speakers, set "SP IMP." to "6Ω MIN" as follows BEFORE using this unit. 4 ohm speakers can be also used as the front speakers. 1 Press LSYSTEM OFF on the front panel to turn off this unit. See page 29 for details. 2 Press and hold MTONE CONTROL and then press KMAIN ZONE ON/OFF to turn on this unit. This unit turns on, and the advanced setup menu appears in the front panel display. ■ AC OUTLET(S) (SWITCHED) U.K. and Australia models 1 outlet Korea model None Other models 2 outlets Use these outlet(s) to supply power to any connected components. Connect the power cable of your other components to these outlet(s). Power to these outlet(s) is supplied when the main zone or Zone 2 is turned on. However, power to these outlet(s) is cut off when the main zone and Zone 2 are turned off or when LSYSTEM OFF on the front panel is pressed. For information on the maximum power or the total power consumption of the components that can be connected to these outlet(s), see "Specifications" on page 127. Note The power to AC OUTLET(S) of this unit is not cut off while this unit is charging connected iPod even when this unit is in the standby mode. When this unit completes charging or the iPod is disconnected, the power is cut off automatically when this unit is in the standby mode. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However, the stored data will be lost in case the power cable is disconnected from the AC wall outlet or if the power supply is cut off for more than one week. TONE CONTROL While holding down MAIN ZONE ON/OFF 3 Rotate the NPROGRAM selector to select "SP IMP.". "SP IMP." and the current speaker impedance setting ("8Ω MIN") appear in the front panel display. 4 Press MTONE CONTROL repeatedly to select "6Ω MIN". 5 Press LSYSTEM OFF to save the new setting and turn off this unit. Note The setting you made is reflected next time you turn on this unit. 28 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
28
En
Connections
■
AC OUTLET(S) (SWITCHED)
U.K. and Australia models
....................................
1 outlet
Korea model
...............................................................
None
Other models
.........................................................
2 outlets
Use these outlet(s) to supply power to any connected
components. Connect the power cable of your other
components to these outlet(s). Power to these outlet(s) is
supplied when the main zone or Zone 2 is turned on. However,
power to these outlet(s) is cut off when the main zone and
Zone 2 are turned off or when
L
SYSTEM OFF
on the front
panel is pressed. For information on the maximum power or
the total power consumption of the components that can be
connected to these outlet(s), see “Specifications” on page 127.
The power to AC OUTLET(S) of this unit is not cut off while this
unit is charging connected iPod even when this unit is in the
standby mode. When this unit completes charging or the iPod is
disconnected, the power is cut off automatically when this unit is
in the standby mode.
1
Press
L
SYSTEM OFF
on the front panel to
turn off this unit.
See page 29 for details.
2
Press and hold
M
TONE CONTROL
and
then press
K
MAIN ZONE ON/OFF
to turn
on this unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
3
Rotate the
N
PROGRAM
selector to select
“SP IMP.”.
“SP IMP.” and the current speaker impedance setting
(“8
Ω
MIN”) appear in the front panel display.
4
Press
M
TONE CONTROL
repeatedly to
select “6
Ω
MIN”.
5
Press
L
SYSTEM OFF
to save the new
setting and turn off this unit.
The setting you made is reflected next time you turn on this
unit.
Connecting the power cable
Note
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, the stored data will be lost in case the power
cable is disconnected from the AC wall outlet or if the
power supply is cut off for more than one week.
AC OUTLETS
SWITCHED
120V 80Hz
100W MAX. TOTAL
0.8A MAX. TOTAL
DVR
MONITOR OUT
C
To the AC wall outlet
(U.S.A. model)
Setting the speaker impedance
Caution
If you are to use 6 ohm speakers, set “SP IMP.” to
“6
Ω
MIN” as follows BEFORE using this unit. 4 ohm
speakers can be also used as the front speakers.
Note
TONE CONTROL
ON/OFF
MAIN ZONE
While holding
down