Yamaha Tio1608-D2 Tio1608-D2 Owners Manual - Page 14

Connection methods, Quick Config (automatic setup)

Get Yamaha Tio1608-D2 PDF manuals and user guides View all Yamaha Tio1608-D2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Connection methods Connection methods This section explains the different methods for connecting the Tio1608-D2 to other Dante devices. To connect to a non-TF series mixer, refer to the mixer instruction manual. Quick Config (automatic setup) When connecting the unit to a TF series mixing console, Quick Config makes it easy to set up the unit automatically. It allows you to connect up to three Tio1608-D2 units to one TF series mixing console, and configures Dante network settings and audio signal settings in one operation. NOTE • To use Quick Config functionality, activate the Tio1608-D compatibility mode. • Tio1608-D2 models can be connected to a mixture of Tio1608D2 and older Tio1608-D models. • An NY64-D audio interface card (sold separately) is required to connect a Tio1608-D2 to a TF series mixing console. Tio1608-D2 procedure 1. With all the units turned off, set the DIP switches on the rear panel to the up position. 2. Set the [QUICK CONFIG FOR TF] on the front panel to the [ON] position. 3. Set the [UNIT ID] on the front panel to the desired position. If you are using multiple Tio1608-D2 units, make sure each unit has a unique UNIT ID setting. 4. Use Ethernet cables to connect the Tio1608-D2 to the NY64-D card (installed in the TF series mixing console) or to other Tio1608-D2 units in a daisychain configuration, as shown below. When using Quick Config, the units will operate the same whether you connect the Ethernet cables to the Dante [PRIMARY] or [SECONDARY]. When connecting 3 units [PRIMARY] or [SECONDARY] TF Series (NY64-D) Tio1608-D2 UNIT ID=1 Tio1608-D2 UNIT ID=2 [PRIMARY] [SECONDARY] [PRIMARY] [SECONDARY] [PRIMARY] or [SECONDARY] Tio1608-D2 UNIT ID=3 5. Turn each device on. TF series mixing console procedure 6. Display the console's SYSTEM SETUP  SLOT SETUP screen, and confirm that Quick Config is enabled. Now the TF series mixing console can recognize the Tio1608-D2 units, and all Dante settings and input and output patching settings will be configured automatically. When the Quick Config button is displayed in white, Quick Config is enabled. If the button is grayed out, click it. If you cannot enable Quick Config, return to step 1 and confirm that the Tio1608-D2 is configured properly. NOTE If used in combination with older Tio1608-D models, specify UNIT ID settings that do not conflict with the Tio1608-D units. Tio1608-D2 Owner's Manual - 14 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Connection methods
-
14
-
Owner’s Manual
Tio1608-D2
Connection methods
This section explains the different methods for connecting
the Tio160
8
-D2 to other Dante devices. To connect to a
non-TF series mixer, refer to the mixer instr
u
ction man
u
al.
Quick Config (automatic setup)
When connecting the
u
nit to a TF series mixing console,
Q
u
ick Config makes it easy to set
u
p the
u
nit a
u
tomatically.
It allo
w
s yo
u
to connect
u
p to three Tio160
8
-D2
u
nits to one
TF series mixing console, and config
u
res Dante net
w
ork
settings and a
u
dio signal settings in one operation.
Tio1608-D2 procedure
1.
With all the units turned off, set the DIP switches on
the rear panel to the up position.
2.
Set the [QUICK CONFIG FOR TF] on the front panel
to the [ON] position.
3.
Set the [UNIT ID] on the front panel to the desired
position.
If you are using multiple Tio1608-D2 units, make
sure each unit has a unique UNIT ID setting.
4.
Use Ethernet cables to connect the Tio1608-D2 to
the NY64-D card (installed in the TF series mixing
console) or to other Tio1608-D2 units in a daisy-
chain configuration, as shown below.
When
u
sing Q
u
ick Config, the
u
nits
w
ill operate the same
w
hether yo
u
connect the Ethernet cables to the Dante
[PRIMARY] or [SECO
N
DARY].
When connecting 3
u
nits
5.
Turn each device on.
TF series mixing console procedure
6.
Display the console's SYSTEM SETUP
SLOT SETUP
screen, and confirm that Quick Config is enabled.
N
o
w
the TF series mixing console can recognize the
Tio160
8
-D2
u
nits, and all Dante settings and inp
u
t and o
u
tp
u
t
patching settings
w
ill be config
u
red a
u
tomatically.
When the Q
u
ick Config b
u
tton is displayed in
w
hite, Q
u
ick
Config is enabled. If the b
u
tton is grayed o
u
t, click it. If yo
u
cannot enable Q
u
ick Config, ret
u
rn to step
1
and confirm that
the Tio160
8
-D2 is config
u
red properly.
NOTE
• To
u
se Q
u
ick Config f
u
nctionality, activate the Tio160
8
-D
compatibility mode.
• Tio160
8
-D2 models can be connected to a mixt
u
re of Tio160
8
-
D2 and older Tio160
8
-D models.
• An
N
Y64-D a
u
dio interface card (sold separately) is req
u
ired to
connect a Tio160
8
-D2 to a TF series mixing console.
NOTE
If
u
sed in combination
w
ith older Tio160
8
-D models, specify U
N
IT
ID settings that do not conflict
w
ith the Tio160
8
-D
u
nits.
TF Series (
N
Y64-D)
Tio160
8
-D2 U
N
IT ID=1
Tio160
8
-D2 U
N
IT ID=2
Tio160
8
-D2 U
N
IT ID=3
[PRIMARY] or
[SECO
N
DARY]
[PRIMARY]
[PRIMARY]
[SECO
N
DARY]
[PRIMARY] or
[SECO
N
DARY]
[SECO
N
DARY]