Yamaha XM4180 Owner's Manual - Page 13

Specifications ■ General Specifications ● XM4180/XM4080 Output Power* 1 kHz, THD+N= 1 % 20 Hz-20 kHz THD+N= 0.1 % Voltage Gain Power Consumption THD+N Intermodulation Distortion Frequency Response SN Ratio Channel Separation Residual Noise Damping Factor Input Sensitivity Maximum Input Voltage Input Impedance Controls Connectors Indicators Load Protection Amplifier Protection Power Supply Protection Cooling Dimensions (W x H x D) Weight Included Accessories 8 Ω/Channel 4 Ω/Channel 8 Ω/Bridged 8 Ω/Channel 4 Ω/Channel 8 Ω/Bridged 70 V/Bridged RL=16 Ω Att. max Standby Idle 1/8 (4 Ω/Pink noise) 20 Hz-20 kHz, Half Power 60 Hz:7 kHz, 4:1, Half Power RL=8 Ω, Po=1 W, HPF=OFF, 20 Hz-20 kHz (DIN AUDIO) Half Power, RL=8 Ω, 1 kHz Att. max, input 600 Ω shunt Att. min, (DIN AUDIO) RL=8 Ω, 1kHz RL=8 Ω, Att. max Front Panel Rear Panel INPUT SPEAKERS MONITOR/REMOTE POWER/STANDBY SIGNAL CLIP/LIMIT PROTECT/MUTE MIN TYP TYP TYP TYP MAX MAX MAX TYP MIN MIN MIN MAX MIN TYP MIN TYP XM4180 210 W x 4 250 W x 4 500 W x 2 180 W x 4 230 W x 4 460 W x 2 300 W x 2 30 dB 5 W 40 W 600 W 0.1 % 0.1 % 0 dB 0 dB -0.5 dB 103 dB XM4080 90 W x 4 120 W x 4 240 W x 2 80 W x 4 115W x 4 230W x 2 - 26 dB 5 W 40 W 400 W 60 dB -73 dBu 100 +4 dBu +22 dBu 20 kΩ (balanced), 10 kΩ (unbalanced) POWER switch (push on/push off) attenuator (31 position) x 4 MODE switch (STEREO/BRIDGE/PARALLEL) x 2 HPF switch (20 Hz/55 Hz/OFF 12 dB/oct) x 2 XLR-3-31 type/ch Euroblock connector (balanced) /ch 5 way binding post/ch Dsub 15P x 1 x 1 (Green/Orange) x 4 (Green) x 4 (Red) x 4 (Red) POWER switch on/off mute DC-fault: output relay off/restored automatically. Clip limiting : THD ≥ 0.5 % Thermal: Cuts the output (when heatsink temp. ≥ 90 °C); operation restored automatically. VI limiter (RL ≤ 2 Ω): Limits the output. Thermal: Power supply shutdown (when temp. ≥ 90 °C); operation not restored automatically. Variable-speed fan x 1 480 x 88 x 412 mm 10 kg 9.8 kg Power cord, Security cover, Owner's Manual, 3-pin Euroblock connector x 4 * These specifications apply to rated power supplies of 120V, 230V and 240V. 0 dBu=0.775 Vrms, Half Power=1/2 Output Power (3 dB below rated power) Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. European models Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 25A Conforms to Environments: E1, E2, E3 and E4 XM4180/XM4080/XH200 Owner's Manual 13 41