Yamaha XM4180 Owner's Manual - Page 14

● XH200 Output Power* Power Consumption THD+N Intermodulation Distortion Frequency Response SN Ratio Channel Separation Residual Noise Input Sensitivity Voltage Gain Maximum Input Voltage Input Impedance Controls 40 Hz-20 kHz THD+N= 0.1 % 70 V, RL=25 Ω 100 V, RL=50 Ω Standby Idle 1/8 (70 V, RL=25 Ω/Pink noise) 40 Hz-20 kHz, Half Power 60 Hz:7 kHz, 4:1, Half Power Po=1 W, HPF=40 Hz, 80 Hz-20 kHz (DIN AUDIO) Half Power, 1 kHz, Att. max, input 600 Ω shunt Att. min, (DIN AUDIO) Att. max Att. max Front Panel MIN MAX MAX MAX TYP MIN MIN MIN MAX TYP TYP MIN TYP Rear Panel Connectors Indicators Load Protection INPUT SPEAKERS MONITOR/REMOTE POWER/STANDBY SIGNAL CLIP/LIMIT PROTECT/MUTE Amplifier Protection Power Supply Protection Cooling Dimensions (W x H x D) Weight Included Accessories 200 W x 2 200 W x 2 5 W 40 W 400 W 0.1 % 0.1 % 0 dB 0 dB -0.5 dB 103 dB 60 dB -65 dBu +4 dBu 38 dB (100 V), 35 dB (70 V) +22 dBu 20 kΩ (balanced), 10 kΩ (unbalanced) POWER switch (push on/push off) attenuator (31 position) x 2 OUTPUT VOLTAGE switch (100 V/70 V) x 1 HPF switch (40 Hz/80 Hz 12 dB/oct) x 2 Euroblock connector (balanced) /ch Barrier strip/ch Dsub 15P x 1 x 1 (Green/Orange) x 2 (Green) x 2 (Red) x 1 (Red) POWER switch on/off mute DC-fault: output relay off/restored automatically. Clip limiting : THD ≥ 0.5 % Thermal: Cuts the output (when heatsink temp. ≥ 90 °C); operation restored automatically. VI limiter (RL ≤ 16 Ω): Limits the output. Thermal: Power supply shutdown (when temp. ≥ 90 °C); operation not restored automatically. Variable-speed fan x 1 480 x 88 x 412 mm 9.8 kg Power cord, Security cover, Owner's Manual, 3-pin Euroblock connector x 2 * These specifications apply to rated power supplies of 120V, 230V and 240V. 0 dBu=0.775 Vrms, Half Power=1/2 Output Power (3 dB below rated power) Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. European models Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 25A Conforms to Environments: E1, E2, E3 and E4 ■ MONITOR/REMOTE PIN layout Pin No. 1 GND Signal XM4180/XM4080 XH200 Description 2 REMOTE CONTROL STANDBY 3 MONITOR MODEL ID STANDBY MODEL ID STANDBY Control: Supply 5 VDC, 5 mADC XM4180: 560 Ω, XM4080: 680 Ω, XH200: 820 Ω (Impedance to GND) 4 REMOTE CONTROL MUTE CH D - MUTE Control: Connect to GND, +5 V, 1 mA 5 MUTE CH C MUTE CH B 6 MUTE CH B - 7 MUTE CH A MUTE CH A 8 MONITOR PROTECT STATUS CH D - PROTECTION Off/ Output On: +5 VDC, Zo=270 Ω 9 PROTECT STATUS CH C PROTECT STATUS CH B PROTECTION On/ Output Off: 0 VDC, Zo=High 10 PROTECT STATUS CH B - 11 PROTECT STATUS CH A PROTECT STATUS CH A 12 OUTPUT LEVEL CH D - XM4180, XM4080 13 OUTPUT LEVEL CH C OUTPUT LEVEL CH B +4dBu (-27.2 dB of Speaker Output Level) at 100 W/8Ω, RL=7.5 kΩ, Zo=300 Ω 14 OUTPUT LEVEL CH B - XH200 15 OUTPUT LEVEL CH A OUTPUT LEVEL CH A -33.2 dB of Speaker Output Level, RL=7.5 kΩ, Zo=300 Ω 14 XM4180/XM4080/XH200 Owner's Manual 42