Yamaha YSP-3300 Owners Manual - Page 26

AUTO SETUP via setup menu

Get Yamaha YSP-3300 PDF manuals and user guides View all Yamaha YSP-3300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Initial settings S/T SETUP X ENTER RETURN AUTO SETUP via setup menu 1 Place the IntelliBeam microphone at your normal listening position, and press the SETUP key. See "Installing the IntelliBeam microphone" (☞p. 23) for instructions on positioning the IntelliBeam microphone. 2 Press the S/T key to select "BEAM" and then press the X key.1) 3 Press the S/T key to select "IntelliBeam" and then press the X key.1) 4 Press the S/T key to select one of the items below and then press the X key.1) Select Item: "BEAM+SOUND OPTIMIZE" (Beam optimization and sound optimization) Select this optimization feature if you make settings for the first time. This menu takes about 3 minutes. "BEAM OPTIMIZE ONLY" (Beam optimization only) Use to optimize the beam angle so that the parameter best matches your listening environment. This menu takes about 1 minute. "SOUND OPTIMIZE ONLY" (Sound optimization only) Use to optimize the beam delay, volume, and quality so that the parameters best match your listening environment. This menu takes about 2 minutes. You must optimize the beam angle with "BEAM OPTIMIZE ONLY" before starting "SOUND OPTIMIZE ONLY". Select this optimization feature in the following cases: • If you have opened or closed the curtains in your listening room before using this unit • If you have manually set the beam angle. 5 Connect the IntelliBeam microphone to this unit after "AUTO SETUP (PREPARATION & CHECK)" screen is displayed. For the details on connecting IntelliBeam microphone, refer to "Using AUTO SETUP (IntelliBeam)" (☞p. 24). 6 Follow steps 4, 5, and 6 under "Using AUTO SETUP (IntelliBeam)" to configure settings, and then remove the microphone. 1) y The ENTER key performs the same function as the X key. 26 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Initial settings
26
En
/
SETUP
RETURN
ENTER
AUTO SETUP via setup menu
1
Place the IntelliBeam microphone at your
normal listening position, and press the
SETUP
key.
See “Installing the IntelliBeam microphone” (
☞
p. 23) for
instructions on positioning the IntelliBeam microphone.
2
Press the
/
key to select “BEAM” and
then press the
key.
1)
3
Press the
/
key to select “IntelliBeam”
and then press the
key.
1)
4
Press the
/
key to select one of the
items below and then press the
key.
1)
Select Item:
“BEAM+SOUND OPTIMIZE”
(Beam optimization and sound optimization)
Select this optimization feature if you make settings for the
first time. This menu takes about 3 minutes.
“BEAM OPTIMIZE ONLY”
(Beam optimization only)
Use to optimize the beam angle so that the parameter best
matches your listening environment. This menu takes about
1 minute.
“SOUND OPTIMIZE ONLY”
(Sound optimization only)
Use to optimize the beam delay, volume, and quality so that
the parameters best match your listening environment. This
menu takes about 2 minutes.
You must optimize the beam angle with “BEAM
OPTIMIZE ONLY” before starting “SOUND OPTIMIZE
ONLY”. Select this optimization feature in the following
cases:
•
If you have opened or closed the curtains in your
listening room before using this unit
•
If you have manually set the beam angle.
5
Connect the IntelliBeam microphone to
this unit after “AUTO SETUP
(PREPARATION & CHECK)” screen is
displayed.
For the details on connecting IntelliBeam microphone,
refer to “Using AUTO SETUP (IntelliBeam)” (
☞
p. 24).
6
Follow steps 4, 5, and 6 under “Using
AUTO SETUP (IntelliBeam)” to configure
settings, and then remove the microphone.
The
ENTER
key performs the same function as the
key.
1)
y