Home » ZyXEL Manuals » Networking » ZyXEL P-314 » Manual Viewer

ZyXEL P-314 User Guide - Page 37

Resetting the Prestige, General Setup

Get ZyXEL P-314 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Prestige 314 PLUS Broadband Sharing Gateway with 4-Port Switch 2.7.1 Resetting the Prestige If you forget your password or cannot access the SMT menu, you will need to reload the factory-default configuration file. Uploading this configuration file replaces the current configuration file with the factorydefault configuration file. This means that you will lose all configurations that you had previously and the speed of the console port will be reset to the default of 9600bps with 8 data bit, no parity, one stop bit and flow control set to none. The password will be reset to "1234", also. Turn off the Prestige and begin a terminal emulation software session with the default console port settings. Turn on the Prestige again. When you see the message "Press Any key to enter Debug Mode within 3 seconds", press any key to enter debug mode. You should already have downloaded the correct file from your nearest ZyXEL FTP site. See section 12.4 for more information on how to transfer the configuration file to your Prestige. Procedure To Use The Reset Button Make sure the SYS led is on (not blinking) before you begin this procedure. Step 1. Press the RESET button for ten seconds, then release it. If the SYS LED begins to blink, the defaults have been restored and the Prestige restarts. Otherwise, go to step 2. Step 2. Turn the Prestige off. Step 3. While pressing the RESET button, turn the Prestige on. Step 4. Continue to hold the RESET button. The SYS LED will begin to blink and flicker very quickly after about 10 or 15 seconds. This indicates that the defaults have been restored and the Prestige is now restarting. 2.8 General Setup Menu 1 - General Setup contains administrative and system-related information (shown next). System Name is for identification purposes. However, because some ISPs check this name you should enter your computer's "Computer Name". • In Windows 95/98 click Start, Settings, Control Panel, Network. Click the Identification tab, note the entry for the Computer Name field and enter it as the System Name. Hardware Installation & Initial Setup 2-9

Section	Page
Copyright	2
Federal Communications Commission (FCC) Interference Statement	3
Information for Canadian Users	4
ZyXEL Limited Warranty	6
Customer Support	7
List of Figures	12
List of Diagrams	16
List of Charts	16
List of Tables	17
Preface	19
Getting to Know Your Prestige 314 PLUS	23
The Prestige Broadband Sharing Gateway With 4-Port Switch	23
Features of the Prestige 314 PLUS	23
Broadband Internet Access via Cable or DSL Modem	26
Internet Access Configuration Checklist	26
Hardware Installation & Initial Setup	29
Front Panel LEDs	29
Prestige Rear Panel and Connections	30
Connecting Your Prestige	31
Additional Installation Requirements	32
Turning on Your Prestige	33
Initial Screen	33
Entering the Password	33
Navigating the SMT Interface	34
Main Menu	35
System Management Terminal Interface Summary	35
Changing the System Password	36
Resetting the Prestige	37
General Setup	37
Dynamic DNS	38
Procedure For Configuring Menu 1	38
Configuring Dynamic DNS	39
WAN Setup	42
LAN Setup	43
LAN Port Filter Setup	43
Internet Access	45
TCP/IP and DHCP for LAN	45
Factory LAN Defaults	45
DHCP Configuration	45
IP Address and Subnet Mask	46
Private IP Addresses	47
RIP Setup	48
IP Multicast	48
IP Alias	49
TCP/IP and DHCP Ethernet Setup	50
IP Alias Setup	52
Internet Access Setup	54
Ethernet Encapsulation	54
PPTP Encapsulation	55
Configure PPTP Client	56
PPPoE Encapsulation	57
Internet Test Setup	58
Basic Setup Complete	59
Network Address Translation (NAT)	63
Introduction	63
NAT Definitions	63
What NAT Does	64
How NAT Works	64
NAT Application	65
NAT Mapping Types	66
Using NAT	68
SUA (Single User Account) Versus NAT	68
Applying NAT	68
NAT Setup	70
Address Mapping Sets	70
Port Forwarding Setup	75
Trigger Port Setup	78
General NAT Examples	80
Internet Access Only	80
Example 2: Internet Access with an Inside Server	82
Example 3: Multiple Public IP Addresses With Inside Servers	82
Example 4: NAT Unfriendly Application Programs	86
Remote Node Setup	89
Remote Node Profile	89
Ethernet Encapsulation	89
PPTP Encapsulation	91
PPPoE Encapsulation	93
Editing TCP/IP Options (with Ethernet Encapsulation)	95
Editing TCP/IP Options (with PPTP Encapsulation)	97
Editing TCP/IP Options (with PPPoE Encapsulation)	99
Remote Node Filter	99
IP Static Route Setup	101
IP Static Route Setup	102
Filter Configuration	107
About Filtering	107
The Filter Structure of the Prestige	108
Configuring a Filter Set	110
Filter Rules Summary Menu	112
Configuring a Filter Rule	113
TCP/IP Filter Rule	113
Generic Filter Rule	118
Example Filter	120
Filter Types and NAT	123
Applying a Filter and Factory Defaults	124
LAN traffic	124
Remote Node Filters	125
UPnP	127
Introducing Universal Plug and Play	127
How do I know if I'm using UPnP?	127
NAT Transversal	127
Cautions with UPnP	128
UPnP and ZyXEL	128
Configuring UPnP	128
Installing UPnP in Windows Example	130
Using UPnP in Windows XP Example	132
SNMP Configuration	137
About SNMP	137
Supported MIBs	139
SNMP Configuration	139
SNMP Traps	140
Traffic Redirect	143
Traffic Redirect	143
Traffic Redirect Setup	145
System Information & Diagnosis	149
System Status	149
To get to the System Status:	150
System Information and Console Port Speed	151
System Information	152
Console Port Speed	153
Log and Trace	154
Viewing Error Log	154
UNIX Syslog	155
Call-Triggering Packet	158
Diagnostic	159
WAN DHCP	160
Firmware and Configuration File Maintenance	163
Filename Conventions	163
Backup Configuration	164
Using the FTP Command from the DOS Prompt	165
Backup Configuration Using TFTP	167
TFTP Command Example	167
Backup Via Console Port	168
Restore Configuration	170
Restore Using FTP or TFTP	170
Restore Via Console Port	172
Uploading Firmware and Configuration Files	173
Firmware File Upload	174
Configuration File Upload	174
TFTP File Upload	176
Uploading Via Console Port	177
System Maintenance & Information	181
Command Interpreter Mode	181
Call Control Support	182
Budget Management	183
Call History	184
Time and Date Setting	185
Time Update Frequency	187
Remote Management	189
Telnet	189
FTP	189
Web	189
DNS (Domain Name System)	190
SNMP (Simple Network Management Protocol)	190
Remote Management Setup	190
Remote Management Limitations	192
Remote Management and NAT	192
System Timeout	192
Call Scheduling	193
Introduction	193
Schedule Setup	193
Schedule Set Setup	194
Applying Schedule Sets to Remote Nodes	196
Troubleshooting	199
Problems Starting Up the Prestige	199
Problems with the LAN Interface	199
Problems with the WAN Interface	200
Problems with Internet Access	201
Appendix APPPoE	203
Appendix B PPTP	206
Appendix DBoot Commands	209
Appendix ENetBIOS Filter Commands	211
Log Descriptions	214
Appendix FPower Adapter Specifications	218
Appendix FHardware Specifications	219

Match case Limit results 1 per page

Prestige 314 PLUS Broadband Sharing Gateway with 4-Port Switch

Hardware Installation & Initial Setup

2-9

2.7.1 Resetting the Prestige

If you forget your password or cannot access the SMT menu, you will need to reload the factory-default

configuration file. Uploading this configuration file replaces the current configuration file with the factory-

default configuration file. This means that you will lose all configurations that you had previously and the

speed of the console port will be reset to the default of 9600bps with 8 data bit, no parity, one stop bit and

flow control set to none. The password will be reset to “1234”, also.

Turn off the Prestige and begin a terminal emulation software session with the default console port settings.

Turn on the Prestige again. When you see the message "Press Any key to enter Debug Mode within 3

seconds", press any key to enter debug mode. You should already have downloaded the correct file from

your nearest ZyXEL FTP site. See

section

12.4 for more information on how to transfer the configuration file

to your Prestige.

Procedure To Use The Reset Button

Make sure the

SYS

led is on (not blinking) before you begin this procedure.

Step 1.

Press the

RESET

button for ten seconds, then release it. If the

SYS

LED begins to blink, the

defaults have been restored and the Prestige restarts. Otherwise, go to step 2.

Step 2.

Turn the Prestige off.

Step 3.

While pressing the

RESET

button, turn the Prestige on.

Step 4.

Continue to hold the

RESET

button. The

SYS

LED will begin to blink and flicker very

quickly after about 10 or 15 seconds. This indicates that the defaults have been restored and

the Prestige is now restarting.

2.8

General Setup

Menu 1 - General Setup

contains administrative and system-related information (shown next).

System

Name

is for identification purposes. However, because some ISPs check this name you should enter your

computer’s “Computer Name”.

•

In Windows 95/98 click

Start

Settings

Control Panel

Network

. Click the

Identification

tab,

note the entry for the

Computer

Name

field and enter it as the

System Name