ASRock G41M-S3 User Manual - Page 20

Onboard Headers and Connectors

Get ASRock G41M-S3 PDF manuals and user guides View all ASRock G41M-S3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

2.8 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! FDD connector (33-pin FLOPPY1) (see p.10 No. 20) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.10 No. 7) PIN1 IDE1 connect the blue end connect the black end to the motherboard to the IDE devices 80-conductor ATA 66/100 cable Note: Please refer to the instruction of your IDE device vendor for the details. SATAII_1 SATAII_3 SATAII_2 SATAII_4 Serial ATAII Connectors (SATAII_1: see p.10, No. 13) (SATAII_2: see p.10, No. 12) (SATAII_3: see p.10, No. 10) (SATAII_4: see p.10, No. 11) These Serial ATAII (SATAII) connectors support SATAII or SATA hard disk for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate. Serial ATA (SATA) Data Cable (Optional) Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on the motherboard. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
20
20
20
20
20
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
FDD connector
(33-pin FLOPPY1)
(see p.10
No. 20)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.10
No. 7)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These Serial ATAII (SATAII)
(SATAII_1: see p.10, No. 13)
connectors support SATAII
(SATAII_2: see p.10, No. 12)
or SATA hard disk for internal
(SATAII_3: see p.10, No. 10)
storage devices. The current
(SATAII_4: see p.10, No. 11)
SATAII interface allows up to
3.0 Gb/s data transfer rate.
Serial ATA (SATA)
Either end of the SATA data cable
Data Cable
can be connected to the SATA /
(Optional)
SATAII hard disk or the SATAII
connector on the motherboard.
F
LO
PPY
1
Pi
n1
the red-striped side to Pin1
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor ATA 66/100 cable
IDE
1
PIN1
SATAII_4
SATAII_3
SATAII_2
SATAII_1