Acer AT310 F1 User Manual - Page 69

Installing a memory module, If the holding clips do not close, the DIMM is not properly - bios

Get Acer AT310 F1 PDF manuals and user guides View all Acer AT310 F1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

51 Installing a memory module Warning! Memory of the identical size, speed, and organization must be installed in the same colored DIMM slots. 1 Perform the pre-installation instructions described on page 28. 2 Remove the side panel described on page 36. 3 Lay the server on its side (components showing). 4 Install the memory module. (1) Align the DIMM so that the notch on the slot fits the keyed edge of the module, then press the module at both ends to seat it fully in the slot. If you insert an DIMM but it does not fit easily in the slot, you have inserted it incorrectly. Reverse the orientation of the module and insert it again. (2) Firmly press the holding clips inward to lock the DIMM in place. If the holding clips do not close, the DIMM is not properly inserted. 5 Observe the post-installation instructions described on page 29. The system automatically detects the amount of memory installed. Run the BIOS setup to view the new value for total system memory and make a note of it.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
51
Installing a memory module
Warning! Memory of the identical size, speed, and organization
must be installed in the same colored DIMM slots.
1
Perform the pre-installation instructions described on page 28.
2
Remove the side panel described on page 36.
3
Lay the server on its side (components showing).
4
Install the memory module.
(1)
Align the DIMM so that the notch on the slot fits the keyed
edge of the module, then press the module at both ends to
seat it fully in the slot.
If you insert an DIMM but it does not fit easily in the slot, you
have inserted it incorrectly. Reverse the orientation of the
module and insert it again.
(2)
Firmly press the holding clips inward to lock the DIMM in
place.
If the holding clips do not close, the DIMM is not properly
inserted.
5
Observe the post-installation instructions described on page 29.
The system automatically detects the amount of memory installed.
Run the BIOS setup to view the new value for total system memory
and make a note of it.