Asus A7V600 SE Motherboard DIY Troubleshooting Guide - Page 28

Jumpers - bios settings

Get Asus A7V600 SE PDF manuals and user guides View all Asus A7V600 SE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

1.11 Jumpers 1. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 sleep mode (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). All jumpers are set to pins 1-2 (+5V) by default because not all computers have the appropriate power supply to support this feature. The USBPW12 and USBPW34 jumpers are for the rear USB ports. The USBPW56 and USBPW78 jumpers are for the internal USB header that you can connect to the front USB ports. 1. This feature requires a power supply that can provide at least 2A on the +5VSB lead when these jumpers are set to +5VSB. Otherwise, the system does not power up. 2. The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal or in sleep mode. USBPW12 USBPW34 12 23 A7V600 SE ® +5V (Default) +5VSB USBPW78 USBPW56 12 23 A7V600 SE USB Device Wake Up +5V (Default) +5VSB 2. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard (the default value is [Disabled]). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS (see section 4.5.1 Power Up Control). A7V600 SE KBPWR 12 23 +5V (Default) +5VSB ® A7V600 SE Keyboard Power Setting 1-18 Chapter 1: Motherboard Information

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
1-18
Chapter 1:
Motherboard Information
1.
USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78)
Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU
stopped, DRAM refreshed, system running in low power mode) using the
connected USB devices. Set to +5VSB to wake up from S3 sleep mode (no
power to CPU, DRAM in slow refresh, power supply in reduced power mode).
All jumpers are set to pins 1-2 (+5V) by default because not all computers have
the appropriate power supply to support this feature.
The USBPW12 and USBPW34 jumpers are for the rear USB ports. The
USBPW56 and USBPW78 jumpers are for the internal USB header that you
can connect to the front USB ports.
1.
This feature requires a power supply that can provide at least 2A
on the +5VSB lead when these jumpers are set to +5VSB.
Otherwise, the system does not power up.
2.
The total current consumed must NOT exceed the power supply
capability (+5VSB) whether under normal or in sleep mode.
A7V600 SE
A7V600 SE USB Device Wake Up
USBPW12
USBPW34
3
2
2
1
+5V
(Default)
+5VSB
USBPW78
USBPW56
3
2
2
1
+5V
(Default)
+5VSB
2.
Keyboard power (3-pin KBPWR)
This jumper allows you to enable or disable the keyboard wake-up feature. Set
this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you
press a key on the keyboard (the default value is [Disabled]). This feature
requires an ATX power supply that can supply at least 1A on the +5VSB lead,
and a corresponding setting in the BIOS (see section 4.5.1 Power Up Control).
A7V600 SE
A7V600 SE Keyboard Power Setting
(Default)
+5V
+5VSB
KBPWR
23
12
1.11
Jumpers